CAN COMMUNICATION SYSTEM > Open in CAN Main Wire |
| Symptom | Trouble Area |
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 69 Ω or higher. |
|

| 1.PRECAUTION |
| NEXT | |
| 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.
| NEXT | |
| 3.CHECK DLC3 |
![]() |
Disconnect the J118 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J118-2 (CANH) - J17-6 (CANH) | Ignition switch OFF | Below 1 Ω |
| J118-13 (CANL) - J17-14 (CANL) | Ignition switch OFF | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - ECM) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J118-1 (CANH) - J118-12 (CANL) | Ignition switch OFF | 108 to 132 Ω |
|
| ||||
| OK | |
| 5.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J118-4 (CANH) - J118-15 (CANL) | Ignition switch OFF | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 6.CONNECT CONNECTOR |
Reconnect the J118 No. 1 junction connector.
| NEXT | |
| 7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - ECM) |
![]() |
Disconnect the J113 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J113-3 (CANH) - J113-14 (CANL) | Ignition switch OFF | 108 to 132 Ω |
|
| ||||
| OK | |
| 8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J113-4 (CANH) - J113-15 (CANL) | Ignition switch OFF | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 9.CONNECT CONNECTOR |
Reconnect the J113 No. 2 junction connector.
| NEXT | |
| 10.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 2 JUNCTION CONNECTOR) |
![]() |
Disconnect the A24 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A24-10 (CANH) - A24-11 (CANL) | Ignition switch OFF | 108 to 132 Ω |
| Result | Proceed to |
| OK (for 1GR-FE) | A |
| OK (for 1UR-FE) | B |
| OK (for 3UR-FE) | C |
| OK (for 3UR-FBE) | D |
| NG | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 11.CONNECT CONNECTOR |
Reconnect the J118 No. 1 junction connector.
| NEXT | |
| 12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ECU - NO. 1 JUNCTION CONNECTOR) |
![]() |
Disconnect the J28 combination meter ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J28-33 (CANH) - J28-34 (CANL) | Ignition switch OFF | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||