DTC B1497/97 BUS IC Communication Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| B1497/97 | Communication line error or open |
|

| 1.PERFORM ACTIVE TEST USING TECHSTREAM |
Select the Active Test, using the Techstream to generate a control command, and then check that the servo motor operates.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Air Mix Servo Targ Pulse (D) | Driver side air mix servo motor pulse | Min.: 5, Max.: 104 | - |
| Air Mix Servo Targ Pulse (P) | Passenger side air mix servo motor pulse | Min.: 6, Max.: 105 | - |
| Air Outlet Servo Pulse (D) | Driver side air outlet servo motor pulse | Min.: 9, Max.: 97 | - |
| Air Inlet Damper Targ Pulse | Air inlet damper target pulse | Min.: 7, Max.: 28 | - |
According to the test, proceed to the next step.
| Result | Proceed to |
| One of the servo motors is malfunctioning | A |
| All of the servo motor are malfunctioning | B |
|
| ||||
| A | |
| 2.SYSTEM CHECK |
According to the test, proceed to the next step.
| Result | Proceed to |
| Only the air mix servo motor (for driver side) is malfunctioning | A |
| Only the air mix servo motor (for passenger side) is malfunctioning | B |
| Only the air outlet servo motor is malfunctioning | C |
| Only the air inlet control servo motor is malfunctioning | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.REPLACE AIR MIX SERVO MOTOR (FOR DRIVER SIDE) |
Replace the air mix servo motor (for driver side) (Click here).
Check for the DTC.
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 4.REPLACE AIR MIX SERVO MOTOR (FOR PASSENGER SIDE) |
Replace the air mix servo motor (for passenger side) (Click here).
Check for the DTC.
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 5.REPLACE AIR OUTLET SERVO MOTOR |
Replace the air outlet servo motor (Click here).
Check for the DTC.
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 6.REPLACE AIR INLET SERVO MOTOR |
Replace the air inlet servo motor (Click here).
Check for the DTC.
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 7.REPLACE AIR CONDITIONING HARNESS |
Replace the air conditioning harness.
Check for the DTC.
| Result | Proceed to |
| DTC B1497/97 is not output | A |
| DTC B1497/97 is output | B |
|
| ||||
| A | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (POWER SOURCE) |
![]() |
Disconnect the J19 air conditioning amplifier connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J19-21(B) - Body ground | Always | 11 to 14 V |
|
| ||||
| OK | ||
| ||