Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B1497/97    BUS IC Communication Malfunction

for Preparation Click here


DESCRIPTION

The air conditioning harness connects the air conditioning amplifier and each servo motor. The air conditioning amplifier supplies power and sends operation instructions to each servo motor through the air conditioning harness. Each servo motor sends the damper position information to the air conditioning amplifier.

DTC Code
DTC Detection Condition
Trouble Area
B1497/97
Communication line error or open
  1. Air conditioning harness
  2. Air mix servo motor (for driver side)
  3. Air mix servo motor (for passenger side)
  4. Air outlet servo motor
  5. Air inlet servo motor
  6. Air cool bypass servo motor
  7. Air conditioning amplifier
  8. Harness or connector

WIRING DIAGRAM


E240335E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Select the Active Test, using the Techstream to generate a control command, and then check that the servo motor operates.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Air Mix Servo Targ Pulse (D)
    Driver side air mix servo motor pulse
    Min.: 5, Max.: 104
    -
    Air Mix Servo Targ Pulse (P)
    Passenger side air mix servo motor pulse
    Min.: 6, Max.: 105
    -
    Air Outlet Servo Pulse (D)
    Driver side air outlet servo motor pulse
    Min.: 9, Max.: 97
    -
    Air Inlet Damper Targ Pulse
    Air inlet damper target pulse
    Min.: 7, Max.: 28
    -
    Cool Air Bypass Pulse
    Driver side cool air bypass pulse
    Min.: 8, Max.: 50
    -

OK:
Arm of the servo motor selected in the Active Test moves smoothly

  1. According to the test, proceed to the next step.
    Result 
    Result
    Proceed to
    One of the servo motors is malfunctioning
    A
    All of the servo motor are malfunctioning
    B



B
Go to step 8
A


2.SYSTEM CHECK
  1. According to the test, proceed to the next step.
    Result 
    Result
    Proceed to
    Only the air mix servo motor (for driver side) is malfunctioning
    A
    Only the air mix servo motor (for passenger side) is malfunctioning
    B
    Only the air outlet servo motor is malfunctioning
    C
    Only the air inlet servo motor is malfunctioning
    D
    Only the cool air bypass servo motor is malfunctioning
    E



B
Go to step 4

C
Go to step 5

D
Go to step 6

E
Go to step 7
A


3.REPLACE AIR MIX SERVO MOTOR (FOR DRIVER SIDE)
  1. Replace the air mix servo motor (for driver side) (Click here ).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.
    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 8
A

END 

4.REPLACE AIR MIX SERVO MOTOR (FOR PASSENGER SIDE)
  1. Replace the air mix servo motor (for passenger side) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.
    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 8
A

END 

5.REPLACE AIR OUTLET SERVO MOTOR
  1. Replace the air outlet servo motor (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.
    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 8
A

END 

6.REPLACE AIR INLET SERVO MOTOR
  1. Replace the air inlet servo motor (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.
    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 8
A

END 

7.REPLACE COOL AIR BYPASS SERVO MOTOR
  1. Replace the cool air bypass servo motor (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.
    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 8
A

END 

8.REPLACE AIR CONDITIONING HARNESS
  1. Replace the air conditioning harness.

    HINT:
    Since the air conditioning harness cannot be inspected while it is removed from the vehicle, replace the air conditioning harness with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.
    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 9
A

END 

9.CHECK HARNESS AND CONNECTOR (POWER SOURCE)


    E240445E01
  1. Disconnect the J19 air conditioning amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    J19-21(B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)