Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING PANEL (for Floor Shift Type)

AIR CONDITIONING PANEL (for Floor Shift Type) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative(-) battery terminal to prevent airbag and seat belt pretensioner activation.



3. REMOVE FRONT DOOR SCUFF PLATE LH
  1. for Regular Cab:
    Remove the front door scuff plate .

  1. for Double Cab:
    Remove the front door scuff plate .

  1. for CrewMax:
    Remove the front door scuff plate .



4. REMOVE COWL SIDE TRIM BOARD LH


B165704
  1. Remove the clip.

  1. Detach the 2 clips and remove the cowl side trim board.



5. REMOVE INSTRUMENT SIDE PANEL LH


    B226739
  1. Using a moulding remover, detach the 7 claws and remove the side panel.



6. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Regular Cab)
  1. Remove the front door opening trim weatherstrip.



7. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Double Cab, CrewMax)
  1. Remove the front door opening trim weatherstrip.



8. REMOVE FRONT PILLAR GARNISH LH


B165843
  1. Detach the 6 claws and 3 clips, and remove the front door scuff plate.



9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B226740
  1. Remove the hood lock control lever.

  1. Remove the 2 bolts.

  1. Detach the 9 clips and claw.



    B163883
  1. for Automatic Air Conditioning System:
    Detach the 2 claws and remove the sensor.

  1. Remove the finish panel and then disconnect the connectors.



10. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B225997
  1. Remove the 4 bolts and remove the instrument panel airbag.

  1. Detach the 2 claws and disconnect the DLC3.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



11. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    B227982
  1. Disconnect the connector and detach the wire harness clamp.

  1. Detach the 12 clips and remove the finish panel.



12. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    B161741
  1. Twist the shift lever knob in the direction indicated by the arrow and remove it.



13. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B161742
  1. Detach the 12 clips and remove the console panel.



14. REMOVE UPPER REAR CONSOLE PANEL SUB-ASSEMBLY
  1. Remove the clip.

  1. Detach the 6 clips and remove the console panel.



  1. w/ Trailer Towing System:
    Disconnect the connector


    B171298



15. REMOVE REAR CONSOLE END PANEL SUB-ASSEMBLY


    B227980
  1. Using a moulding remover, detach the 7 clips and remove the end panel.

  1. except Regular Cab:
    Detach the 2 wire harness clamps and disconnect the connector.



16. REMOVE CONSOLE BOX CARPET


17. REMOVE REAR CONSOLE BOX ASSEMBLY


    B227981
  1. Remove the 2 screws.

  1. Detach the 2 wire harness clamps.

  1. Remove the 4 bolts and rear console box.



18. REMOVE FRONT CONSOLE BOX


    B161746
  1. Remove the 2 clips.

  1. Remove the 6 screws and front console box.



19. REMOVE CENTER LOWER INSTRUMENT PANEL FINISH PANEL


    B227982
  1. Disconnect the connector and detach the wire harness clamp.

  1. Detach the 12 clips and remove the finish panel.



20. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


E146074E04
  1. Detach the 4 clips.

  1. Disconnect the connector and remove the panel.



21. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ USB Audio System)


    B229224
  1. Remove the 4 bolts.



    B229225
  1. Pull the radio receiver to detach the 3 clips on the backside of the radio receiver.

  1. Disconnect the connectors and remove the radio receiver.



22. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o USB Audio System)


    B164786
  1. Remove the 4 bolts.



    E159007
  1. Pull the radio receiver to detach the 3 clips on the backside of the radio receiver.

  1. Disconnect the connectors and remove the radio receiver.



23. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)
  1. for DVD:
    Remove the navigation receiver assembly with bracket .

  1. for SD:
    Remove the navigation receiver assembly with bracket .