Home › BODY › INTERIOR › ROOF HEADLINING (for CrewMax)

ROOF HEADLINING (for CrewMax) > INSTALLATION

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL ROOF HEADLINING ASSEMBLY


B166622
  1. Place the roof headlining into the cabin as shown in the illustration.

    NOTICE:
    Be careful not to damage the roof headlining when placing it in the cabin.



  1. w/o Sliding Roof:



    1. Attach the 4 clips to install the roof headlining.


      B169219E05



  1. w/ Sliding Roof:



    1. Attach the 4 clips and 14 fasteners to install the roof headlining.


      B229096E01



    B229072
  1. Connect the roof wire connector and attach the 3 clamps.



    B167283
  1. w/ EC Mirror:

    1. Connect the EC mirror connector.



2. INSTALL ASSIST GRIP PLUG


B165717
  1. Install a new assist grip plug.



3. INSTALL ASSIST GRIP SUB-ASSEMBLY


B169217

HINT:
Use the same procedure for the other 2 assist grips.

  1. Install the 2 clips and 2 covers to the assist grip, as shown in the illustration.

  1. Install the assist grip.



4. INSTALL VISOR HOLDER


B165713

HINT:
Use the same procedure to install the visor holder on the other side.

  1. Install the visor holder with the screw.



5. INSTALL VISOR ASSEMBLY LH


B165715
  1. Install the visor assembly LH with the 3 screws.



6. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



7. INSTALL VISOR BRACKET COVER LH


B166262
  1. Attach the 4 claws to install the visor bracket cover.



8. INSTALL VISOR BRACKET COVER RH

HINT:
Use the same procedures described for the LH side.



9. INSTALL ROOM LIGHT ASSEMBLY


  1. w/o Rear Seat Entertainment System:

    1. Connect the connector.

    2. Attach the 4 clips to install the room light.



    3. Attach the 4 claws to install the lens.


      B165837



    B169221
  1. w/ Rear Seat Entertainment System:

    1. Connect the connectors.

    2. Attach the 4 clips to install the room light.

      NOTICE:
      When installing the room light, be careful not to damage the shaded areas in the illustration.



10. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


B227101
  1. Attach the 2 claws of the inner rear view mirror stay holder cover to the mirror, and then slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration to attach the 2 claws to the roof headlining and install the inner rear view mirror stay holder cover.



11. INSTALL ROOF CONSOLE BOX ASSEMBLY
  1. for Short Type:
    Install the roof console box .

  1. for Long Type:
    Install the roof console box .



12. INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


B169215
  1. Slide the rear shoulder belt anchor plate in the direction shown in the illustration and attach the 4 claws to install the plate.



13. INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



14. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH


B169213
  1. Pass the rear seat outer belt floor anchor through the front quarter trim panel.

  1. Attach the 4 clips to install the quarter trim panel.

  1. Install the 2 bolts.



    B165712
  1. Attach the claw to install the cover.



15. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



16. INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY LH


B169212
  1. Attach the 4 clips to install the lower quarter trim panel.



    B165831
  1. Connect the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B165830
  1. Attach the 2 claws to install the cover.



17. INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY RH


B173407
  1. Attach the 3 clips to install the lower quarter trim panel.



    B173410
  1. Connect the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B173409
  1. Attach the 2 claws to install the cover.



18. INSTALL BACK PANEL TRIM LH
  1. Attach the 8 clips to install the back panel trim.



  1. Install the package holder net hook.


    B170105E05



19. INSTALL BACK PANEL TRIM RH


B169224E05
  1. Attach the 8 clips to install the back panel trim.

  1. Install the package holder net hook.



20. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


B166614
  1. Slide the front shoulder belt anchor plate in the direction shown in the illustration and attach the 6 claws to install the plate.



21. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



22. INSTALL CENTER PILLAR GARNISH LH
  1. Pass the front seat outer belt floor anchor through the center pillar garnish.

  1. Attach the claw to install the center pillar garnish.

  1. Install the 2 screws.

  1. Install the assist grip with the 2 bolts.



  1. Attach the 2 claws to install the 2 assist grip plugs.


    B165826



23. INSTALL CENTER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



24. INSTALL LOWER CENTER PILLAR GARNISH LH


B165829
  1. Attach the 7 clips and 2 claws to install the lower center pillar garnish.



    B165828
  1. Connect the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B165827
  1. Attach the 2 claws to install the cover.



25. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



26. INSTALL FRONT PILLAR GARNISH LH
  1. Attach the claw to install the front pillar garnish.

  1. Install the assist grip with the 2 bolts.



  1. Attach the 2 claws to install the 2 assist grip plugs.


    B165706



27. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



28. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the rear door opening trim weatherstrip.



29. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the rear door opening trim weatherstrip.



30. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip.



31. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip.



32. INSTALL COWL SIDE TRIM BOARD LH


B165704
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the clip.



33. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



34. INSTALL REAR DOOR SCUFF PLATE LH


B169218
  1. Attach the 8 claws and 2 clips to install the rear door scuff plate.



35. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



36. INSTALL FRONT DOOR SCUFF PLATE LH


B165841
  1. Attach the 6 claws and 3 clips to install the front door scuff plate.



37. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



38. INSTALL REAR SEAT ASSEMBLY (for CrewMax LH Side)
  1. Install the rear seat assembly (Click here).



39. INSTALL REAR SEAT ASSEMBLY (for CrewMax RH Side)
  1. Install the rear seat assembly (Click here).



40. INSTALL FRONT SEAT ASSEMBLY (for Center Seat)
  1. Install the front seat assembly (Click here).



41. INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)
  1. Install the front seat assembly (Click here).



42. INSTALL FRONT SEAT ASSEMBLY (for Power Seat)
  1. Install the front seat assembly (Click here).



43. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


44. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).