Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat)

FRONT SEAT ASSEMBLY (for Manual Seat) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.



1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.



    B255936
  1. Install the front seat side airbag assembly with 2 new nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the 2 clamps.



    B255935
  1. Connect the 3 wire harness clamps to under the seat.



2. INSTALL FRONT SEAT WIRE LH


3. INSTALL SEAT POSITION AIRBAG SENSOR


    C108775E04
  1. Check that the ignition switch is OFF.

  1. Check that the cable is disconnected from the battery negative (-) terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

    NOTICE:
    Some systems need to be initialized after the cable is reconnected (Click here).



    C107067E04
  1. Using a feeler gauge 1.0 mm (0.0393 in.), install the seat position sensor.

    NOTICE:
    1. If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
    2. When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

    HINT:
    Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 to 1.4 mm (0.0236 to 0.0551 in.).

  1. Using a T30 "TORX" socket wrench, install the seat position sensor with the screw.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 to 1.4 mm (0.0236 to 0.0551 in.).

  1. Check that there is no looseness in the installation parts of the seat position sensor.

  1. Connect the connector.

  1. Install the seat slide position sensor protector to the seat position sensor.



4. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side)


B165540
  1. Attach the claw to install the ECU.

  1. Connect the 2 ECU connectors.



5. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar Support Adjuster)


    B167110
  1. Attach the 3 claws to install the bush.



    B167109
  1. Install the lumbar support adjuster with the 2 screws.

  1. Connect the lumbar support adjuster connector.



    B167105E06
  1. Attach the 6 hooks to install the seatback spring.

  1. Install the 2 springs.



6. INSTALL LOWER FRONT SEAT CUSHION SHIELD RH


B166418
  1. Attach the claw to install the cushion shield lower.



7. INSTALL LOWER FRONT SEAT CUSHION SHIELD LH
  1. Attach the claw to install the cushion shield lower.



8. INSTALL RECLINING ADJUSTER INSIDE COVER RH


B165538
  1. Attach the claw to install the reclining adjuster inside cover.

  1. Install the screw.



9. INSTALL RECLINING ADJUSTER INSIDE COVER LH
  1. Attach the claw to install the reclining adjuster inside cover.

  1. Install the screw.



10. INSTALL RECLINING ADJUSTER INSIDE COVER RH


B165537
  1. Install the reclining adjuster inside cover with the screw.



11. INSTALL RECLINING ADJUSTER INSIDE COVER LH
  1. Install the reclining adjuster inside cover with the screw.



12. INSTALL SEPARATE TYPE FRONT SEATBACK COVER LH


    B166538E01
  1. Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B166411
  1. Connect the seatback cover bracket to the seatback pad.



    B165532E02
  1. Install the seatback cover wires.

  1. Using hog ring pliers, install new hog rings to the seatback pad.



13. INSTALL FRONT SEATBACK COVER WITH PAD LH
  1. Install the seatback cover with pad to the seatback frame.



    B165534E02
  1. Using hog ring pliers, install new hog rings to the seat frame.



    B165529
  1. Attach the 4 claws to install the 2 headrest supports.



    B165533
  1. Connect the seatback cover bracket to the seat frame and install the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.



    B165531E02
  1. Install the seatback cover wires.

  1. Using hog ring pliers, install new hog rings to the seat frame.



    B165530E02
  1. Attach the hook.



14. INSTALL FRONT SEAT HEADREST ASSEMBLY LH


15. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER LH


B166539E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



16. INSTALL FRONT SEAT CUSHION COVER WITH PAD LH


    B165526E05
  1. Attach the hooks to install the seat cushion cover with pad.

  1. Using hog ring pliers, install new hog rings.

  1. Bend the 2 seat frame claws downward.



    B165527
  1. Install the 2 clips.



17. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


B166599E01
  1. Install the front seat inner belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt to overlap the protruding part of the front seat adjuster.

  1. Driver Side:

    1. Connect the 2 connectors and attach the 4 clamps.

  1. Passenger Side:
    Connect the connector and attach the clamp.



18. INSTALL INNER FRONT SEAT CUSHION SHIELD LH


B166410E01
  1. Attach the 3 claws in the order shown in the illustration, and install the cushion shield.

  1. Install the screw.



19. INSTALL FRONT POWER SEAT LUMBAR SWITCH (w/ Lumbar Support Adjuster)


    B194037
  1. Install the switch with the 2 screws.



20. INSTALL FRONT SEAT CUSHION SHIELD LH


B166409E01
  1. w/ Lumbar Support Adjuster:
    Connect the switch connector.

  1. Attach the 3 claws in the order shown in the illustration, and install the cushion shield.

  1. Install the 2 screws.



    B165523E03
  1. Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with new hog rings.



21. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


B165804
  1. Attach the claw to install the reclining adjuster release handle.



22. INSTALL VERTICAL SEAT ADJUSTER KNOB LH (for 8 Way Seat Type)
  1. Install the snap ring to the vertical seat adjuster knob.



    B166938
  1. Install the vertical seat adjuster knob to the front seat.



23. INSTALL VERTICAL ADJUSTING HANDLE LH (for 8 Way Seat Type)


    B165520
  1. Install the vertical adjusting handle with the 2 screws.



    B165519
  1. Attach the 2 claws to install the vertical adjusting handle cap.