Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › FRONT SEAT SIDE AIRBAG ASSEMBLY (for Fold Down Seat Type)

FRONT SEAT SIDE AIRBAG ASSEMBLY (for Fold Down Seat Type) > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.



1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.



    B255630
  1. Install the front seat side airbag assembly with 2 new nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the clamp.



2. INSTALL FRONT SEATBACK COVER WITH PAD RH
  1. Install the seatback cover with pad to the seatback spring.



    B165529
  1. Attach the 4 claws to install the 2 headrest supports.



    B166421E01
  1. Using hog ring pliers, install new hog rings to the seatback spring.



    B166422E01
  1. Using hog ring pliers, install new hog rings to the seatback spring.



    B165552
  1. Connect the seatback cover bracket to the seatback spring and install the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.

  1. Using hog ring pliers, install new hog rings to the seatback cover.



3. INSTALL FRONT SEATBACK LOCK SUB-ASSEMBLY RH


B166555
  1. Install the seatback lock with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



4. INSTALL FRONT SEATBACK LOCK HANDLE ROD


B165799
  1. Install the seatback lock handle rod.

    NOTICE:
    Install the rod as shown in the illustration.



5. INSTALL FRONT SEATBACK LOCK SUB-ASSEMBLY LH


B165550
  1. Install the seatback lock with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    NOTICE:
    Connect the rod and seatback lock before installing the bolts.



6. INSTALL FRONT SEATBACK BOARD


B166549E01
  1. Attach the 2 hooks to install the seatback board, and then attach the 2 clips.



7. INSTALL FRONT SEATBACK ASSEMBLY RH


B165548
  1. Install the seatback with the 4 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    B255629
  1. Connect the 3 airbag wire harness clamps to under the seat.



8. INSTALL FRONT SEATBACK SHIELD RH


    B165546
  1. Connect the airbag wire harness to the seatback shield.



    B165545
  1. Attach the 2 claws to install the seatback shield.

  1. Install the screw.



9. INSTALL FRONT SEATBACK SHIELD LH
  1. Attach the 2 claws to install the seatback shield.

  1. Install the screw.



10. INSTALL FRONT SEATBACK LOCK HANDLE RH


B165808


11. INSTALL FRONT SEATBACK LOCK HANDLE LH


12. INSTALL FRONT SEAT HEADREST ASSEMBLY RH


13. INSTALL INNER FRONT SEAT CUSHION SHIELD RH


B166414E01
  1. Attach the 3 claws in the order shown in the illustration, and install the cushion shield.

  1. Install the screw.



14. INSTALL FRONT SEAT CUSHION SHIELD RH


B166413E01
  1. Attach the 3 claws in the order shown in the illustration, and install the cushion shield.

  1. Install the 2 screws.



    B165523E02
  1. Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with new hog rings.



15. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH


B165803
  1. Attach the claw to install the reclining adjuster release handle.



16. INSTALL FRONT SEAT ASSEMBLY RH
  1. Install the front seat assembly RH (Click here).



17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).