Home › BODY › SEAT › FRONT SEAT CUSHION HEATER (w/ Seat Heater System or Climate Control Seat System)

FRONT SEAT CUSHION HEATER (w/ Seat Heater System or Climate Control Seat System) > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.



1. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH
  1. w/ Seat Heater System:
    Set the seat cushion heater with the name stamp side facing the seat cushion cover.



  1. Install the seat cushion heater with new tack pins.


    B167119E01

  1. w/ Climate Control Seat System:
    Set the seat cushion heater with the name stamp side facing the seat cushion cover.



  1. Install the seat cushion heater with new tack pins.


    B227987E01



2. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER LH


    B166539E02
  1. w/o Leg Support Adjustment Switch:
    Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. w/ Leg Support Adjustment Switch:
    Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.

    2. When installing the hog rings, avoid wrinkling the cover.


      B167196E01



3. INSTALL FRONT SEAT CUSHION COVER WITH PAD LH


    B167115E02
  1. w/o Leg Support Adjustment Switch:

    1. Attach the hooks to install the seat cushion cover with pad.

    2. Using hog ring pliers, install new hog rings.

    3. Bend the 2 seat frame claws downward.



    B167190
  1. w/ Leg Support Adjustment Switch:

    1. Install the seat cushion cover with pad to the seat frame.

    2. Install the seat cushion cover wire.



    3. B166950E02
    4. Using hog ring pliers, install new hog rings and attach the hooks.

      HINT:
      When installing the leg support hog rings, press the seat cushion cover with pad against the seat frame.



    B227991
  1. Attach the wire harness clamp.



  1. w/ Seat Heater System or Climate Control Seat System:



      B179848
    1. Connect the seat heater control connector and attach the 2 wire harness clamps.



    2. B179847
    3. Connect the seat heater connector and attach the 2 wire harness clamps.



    B167097
  1. Install the 2 clips.



4. INSTALL FRONT POWER SEAT SWITCH LH


B166949
  1. Install the switch with the 3 screws.

  1. Connect the 2 switch connectors.

  1. w/o Seat Position Memory System:
    Connect the switch connector.



5. INSTALL INNER FRONT SEAT CUSHION SHIELD LH


B166948
  1. Attach the 2 claws and clip to install the cushion shield.

  1. Install the screw.



6. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


B166599E01
  1. Install the front seat inner belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt to overlap the protruding part of the front seat adjuster.

  1. Driver Side:

    1. Connect the 2 connectors and attach the 4 clamps.

  1. Passenger Side:
    Connect the connector and attach the clamp.



7. INSTALL FRONT SEAT CUSHION SHIELD LH


B166945
  1. Connect the switch connectors.

  1. Attach the 2 claws to install the cushion shield.

  1. Install the 3 screws.



    B166944E02
  1. Install the 2 screws.

  1. Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with new hog rings.



8. INSTALL RECLINING POWER SEAT SWITCH KNOB LH


B167192
  1. Attach the 2 claws to install the knob.



9. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB LH


B167193
  1. Attach the 2 claws to install the knob.



10. INSTALL FRONT SEAT ASSEMBLY LH
  1. Install the front seat (Click here).