Home › TRANSMISSION ยท A760F AUTOMATIC TRANSMISSION › TRANSMISSION CONTROL CABLE (for Column Shift Type)

TRANSMISSION CONTROL CABLE (for Column Shift Type) > INSTALLATION

for Preparation Click here



1. INSTALL COLUMN SHIFT TRANSMISSION CONTROL CABLE ASSEMBLY


C157286
  1. Insert the transmission control cable from the vehicle interior, and install the cable retainer with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



    C158378
  1. Connect the cable to the steering column shaft bracket so that the claws of the outer cable socket are securely attached.



    C158379E01
  1. Connect the column shift transmission control cable end to the column shift.

    NOTICE:
    Make sure to connect the cable end so that the inner cable is not twisted. Confirm that the ridged side of the cable end is facing upward.



    C157289
  1. Connect the 2 cable clamps with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Return the floor carpet to its original position.

  1. Move the shift lever to N.



    C155873E01
  1. Turn the control shaft lever counterclockwise until it stops, and then turn it clockwise 2 notches to set it to the N position.



    C158380E01
  1. Connect the control cable with a new clip and the nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    NOTICE:
    When connecting the cable to the transmission control shaft lever, make sure the L bracket of the cable faces the inside of the vehicle.



    C157285
  1. Connect the transmission control cable support with the nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



2. INSTALL FRONT SEAT ASSEMBLY LH
  1. for Manual Seat Type:
    Install the front seat LH (Click here).

  1. for Power Seat Type:
    Install the front seat LH (Click here).

  1. for Center Seat:
    Install the front seat LH (Click here).

  1. for Fold Down Seat:
    Install the front seat LH (Click here).



3. ADJUST SHIFT LEVER POSITION
  1. Move the shift lever to N.



    C155901E01
  1. Fold back the transmission control cable adjust case cover. Then while sliding the slider toward the cable end side, press out the lock piece from the back side to release the lock.



    C155902E01
  1. Check that the spring of the adjust case is applying enough tension to the shift control cable. Then press in the lock piece to set the lock.

    NOTICE:
    1. Use your hand to push in the lock piece. Do not use any tools.
    2. Securely push in the lock piece so that the protrusion of the slider is above the lock piece.

  1. Return the cover of the adjust case to its original position.

  1. Inspect the shift lever operation after the adjustment.



4. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from N to other positions, check that the lever can be moved smoothly and accurately to each position and that the position indicator comes on in accordance with the shift lever position.
    If the indicator and shift lever position do not match, carry out the following adjustment procedures.



5. INSTALL UPPER STEERING COLUMN COVER


C154520
  1. Attach the claw to install the upper steering column cover.

  1. Attach the 4 clips.



6. INSTALL LOWER STEERING COLUMN COVER


C154519
  1. Attach the 2 claws to install the lower steering column cover.

  1. Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



7. INSTALL STEERING WHEEL ASSEMBLY


C159526E01
  1. Align the matchmarks on the steering wheel and steering main shaft.

  1. Install the steering wheel set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



8. INSTALL STEERING PAD (w/ Steering Pad Switch)


    B166581
  1. Support the steering pad with one hand.

  1. Connect the 2 connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Confirm that the circumference groove of the screw fits in the screw case, and place the steering pad onto the steering wheel .

  1. Using a T30 "TORX" socket wrench, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



9. INSTALL STEERING PAD (w/o Steering Pad Switch)


    B166435
  1. Support the steering pad with one hand.

  1. Connect the 2 connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Confirm that the circumference groove of the screw fits in the screw case, and place the steering pad onto the steering wheel.

  1. Using a T30 "TORX" socket wrench, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



10. INSTALL CENTER LOWER INSTRUMENT COVER


  1. Install the cover with the 2 clips.


    B171284E01



11. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B225998
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Attach the 2 claws to install the DLC3.

  1. Install the 4 bolts to install the instrument panel airbag.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



12. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B163883
  1. for Automatic Air Conditioning System:
    Attach the 2 claws to install the sensor.



    B226740
  1. Connect the connectors.

  1. Attach the 9 clips and claw to install the finish panel.

  1. Install the 2 bolts.

  1. Install the hood lock control lever.



13. INSTALL COWL SIDE TRIM BOARD LH


B165704
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the clip.



14. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab, CrewMax)


B165841
  1. Attach the 6 claws and 3 clips to install the front door scuff plate.



15. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab)


B165843
  1. Attach the 6 claws and 3 clips to install the front door scuff plate.



16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL