TRANSMISSION CONTROL CABLE (for Column Shift Type) > INSTALLATION |
| 1. INSTALL COLUMN SHIFT TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Insert the column shift transmission control cable from the vehicle interior, and install the cable retainer with the 2 bolts.
![]() |
Connect the cable to the steering column shaft bracket so that the outer cable socket's claws attach securely.
![]() |
Connect the column shift transmission control cable end to the column shift.
![]() |
Connect the 2 cable clamps with the 2 bolts.
Return the floor carpet front LH side to its original position.
Move the shift lever to the N position.
![]() |
Turn the control shaft lever counterclockwise until it stops, and then turn it clockwise 2 notches to set it to the N position.
![]() |
Connect the control cable with a new clip and the nut.
![]() |
Connect the transmission control cable support with the nut.
| 2. INSTALL FRONT SEAT ASSEMBLY LH |
for Power Seat Type:
Install the front seat LH (Click here).
for Manual Seat Type:
Install the front seat LH (Click here).
| 3. ADJUST SHIFT LEVER POSITION |
Move the shift lever to the N position.
![]() |
Fold back the transmission control cable adjust case cover. Then while sliding the slider toward the cable end side, press the lock piece from the back side to release the lock.
![]() |
Check that the adjust case's spring is applying enough tension to the shift control cable. Then press the lock piece to set the lock.
Return the cover of the adjust case to its original position.
Inspect the operation after the adjustment.
| 4. INSPECT SHIFT LEVER POSITION |
When moving the shift lever from the N position to other positions, check that the lever can be shifted smoothly and accurately to each position and that the position indicator comes on in accordance with the shift lever position.
If the indicator and shift lever position do not match, carry out the following adjustment procedures.
| 5. INSTALL UPPER STEERING COLUMN COVER |
![]() |
Attach the claw to install the upper steering column cover.
Attach the 4 clips.
| 6. INSTALL LOWER STEERING COLUMN COVER |
![]() |
Attach the 2 claws to install the lower steering column cover.
Install the 2 screws.
| 7. INSTALL STEERING WHEEL ASSEMBLY |
![]() |
Align the matchmarks on the steering wheel and steering main shaft.
Install the steering wheel set nut.
| 8. INSTALL STEERING PAD (w/ Steering Pad Switch) |
![]() |
Support the steering pad with one hand.
Connect the 2 connectors to the steering pad.
Confirm that the circumference groove of the screw fits in the screw case, and place the steering pad onto the steering wheel .
Using a T30 "TORX" socket wrench, tighten the 2 screws.
| 9. INSTALL STEERING PAD (w/o Steering Pad Switch) |
![]() |
Support the steering pad with one hand.
Connect the 2 connectors to the steering pad.
Confirm that the circumference groove of the screw fits in the screw case, and place the steering pad onto the steering wheel .
Using a T30 "TORX" socket wrench, tighten the 2 screws.
| 10. INSTALL CENTER LOWER INSTRUMENT COVER |
Install the cover with the 2 clips.

| 11. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY |
![]() |
Connect the connector.
Attach the 2 claws to install the DLC3.
Install the 4 bolts to install the instrument panel airbag.
| 12. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH |
![]() |
for Automatic Air Conditioning System:
Attach the 2 claws to install the sensor.
![]() |
Connect the connectors.
Attach the 9 clips and claw to install the finish panel.
Install the 2 bolts.
Install the hood lock control lever.
| 13. INSTALL COWL SIDE TRIM BOARD LH |
![]() |
Attach the 2 clips to install the cowl side trim board.
Install the clip.
| 14. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab, CrewMax) |
![]() |
Attach the 6 claws and 3 clips to install the front door scuff plate.
| 15. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab) |
![]() |
Attach the 6 claws and 3 clips to install the front door scuff plate.
| 16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |