Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › SPIRAL CABLE

SPIRAL CABLE > INSTALLATION

for Preparation Click here



1. INSTALL SPIRAL CABLE


    B166448
  1. Attach the 3 claws and install the spiral cable with steering sensor.

    NOTICE:
    When replacing the spiral cable with a new one, remove the lock pin before installing the steering wheel.

  1. Connect the connectors to the spiral cable with steering sensor.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



2. INSTALL UPPER STEERING COLUMN COVER


C154520
  1. Attach the claw to install the upper steering column cover.

  1. Attach the 4 clips.



3. INSTALL LOWER STEERING COLUMN COVER


C154519
  1. Attach the 2 claws to install the lower steering column cover.

  1. Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



4. ADJUST SPIRAL CABLE


    B166449
  1. Check that the ignition switch is OFF.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  1. Rotate the spiral cable with steering sensor counterclockwise slowly by hand until it feels firm.

    NOTICE:
    Do not turn the spiral cable with steering sensor by the airbag wire harness.



    B166450
  1. Rotate the spiral cable with steering sensor clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable with spiral sensor by the airbag wire harness.

    HINT:
    The spiral cable with steering sensor will rotate approximately 2.5 turns to both the left and right from the center.



5. INSTALL STEERING WHEEL ASSEMBLY


C159526E01
  1. Align the matchmarks on the steering wheel and steering main shaft.

  1. Install the steering wheel set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



6. INSTALL STEERING PAD


    B166581
  1. Support the steering pad with one hand.

  1. Connect the 2 connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Confirm that the circumference groove of the screw fits in the screw case, and place the steering pad onto the steering wheel .

  1. Using a T30 "TORX" socket wrench, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



7. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    B166432
  1. Attach the 2 claws to install the cover.



8. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    B166433
  1. w/ Cruise Control:

    1. Attach the 2 claws to install the cover.



    B167059
  1. w/o Cruise Control:

    1. Attach the 2 claws to install the cover.



9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



10. INSPECT STEERING PAD
  1. With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
    Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.

  1. Check that the horn sounds.
    If the horn does not sound, inspect the horn system.



11. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).