Home › STEERING › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)

STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) > INSTALLATION

for Preparation Click here



1. INSTALL STEERING COLUMN ASSEMBLY


C159218
  1. Install the steering column with the bolt and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



2. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


C155151E01
  1. Align the matchmarks on the No. 2 steering intermediate shaft and power steering gear.

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



3. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY


C155150E01
  1. Align the matchmarks on the steering intermediate shaft and No. 2 steering intermediate shaft.

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



    C154524E01
  1. Align the matchmarks on the steering column and steering intermediate shaft.

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



    C155149
  1. Install the 3 bolts and nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



4. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY


C154523
  1. Install the air duct with the bolt.



5. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY


    B225998
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Attach the 2 claws to install the DLC3.

  1. Install the 4 bolts to install the instrument panel airbag.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



6. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B163883
  1. for Automatic Air Conditioning System:
    Attach the 2 claws to install the sensor.



    B226740
  1. Connect the connectors.

  1. Attach the 9 clips and claw to install the finish panel.

  1. Install the 2 bolts.

  1. Install the hood lock control lever.



7. INSTALL INSTRUMENT SIDE PANEL LH


    B229058
  1. Attach the 7 claws to install the side panel.



8. INSTALL COWL SIDE TRIM BOARD LH


B165704
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the clip.



9. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab)


B165843
  1. Detach the 6 claws and 3 clips, and remove the front door scuff plate.



10. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab, CrewMax)


B165841
  1. Attach the 6 claws and 3 clips to install the front door scuff plate.



11. INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


C159216
  1. Install the combination switch assembly with spiral cable to the steering column assembly with the clamp.



    C154522
  1. Connect the 5 connectors to the combination switch with spiral cable.



12. INSTALL UPPER STEERING COLUMN COVER


C159215
  1. Attach the claw to install the upper steering column cover.

  1. Attach the 4 clips.



13. INSTALL LOWER STEERING COLUMN COVER


C154519
  1. Attach the 2 claws to install the column cover.

  1. Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



14. INSTALL TILT AND TELESCOPIC MANUAL SWITCH


C159804
  1. Attach the claw to install the tilt and telescopic switch.

  1. Connect the connector.



15. INSTALL STEERING WHEEL ASSEMBLY


C159526E01
  1. Align the matchmarks on the steering wheel and steering main shaft.

  1. Install the steering wheel set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



16. INSPECT STEERING WHEEL CENTER POINT


17. INSTALL STEERING PAD (w/ Steering Pad Switch)


    B166581
  1. Support the steering pad with one hand.

  1. Connect the 2 connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Confirm that the circumference groove of the screw fits in the screw case, and place the steering pad onto the steering wheel .

  1. Using a T30 "TORX" socket wrench, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



18. INSTALL STEERING PAD (w/o Steering Pad Switch)


    B166435
  1. Support the steering pad with one hand.

  1. Connect the 2 connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Confirm that the circumference groove of the screw fits in the screw case, and place the steering pad onto the steering wheel.

  1. Using a T30 "TORX" socket wrench, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



19. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    B166432
  1. Attach the 2 claws to install the cover.



20. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    B166433
  1. w/ Cruise Control:

    1. Attach the 2 claws to install the cover.



    B167059
  1. w/o Cruise Control:

    1. Attach the 2 claws to install the cover.



21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Some systems need to be initialized after the cable is reconnected (Click here).



22. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).