Home › DRIVE LINE › JF1A TRANSFER › TRANSFER CASE FRONT OIL SEAL

TRANSFER CASE FRONT OIL SEAL > REPLACEMENT

for Preparation Click here



1. DRAIN TRANSFER OIL


    C159809
  1. Remove the 4 bolts and lower transfer case protector.

  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the transfer oil.



2. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
  1. Remove the front propeller shaft (Click here).



3. REMOVE FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


    C180857E02
  1. Using SST and a hammer, loosen the staked part of the transfer output shaft nut.

    SST
    09930-00010  

    NOTICE:
    1. Be sure to use SST with the tapered surface facing the shaft.
    2. Do not grind the tip of SST with a grinder or other device.
    3. Completely loosen the staked part of the transfer output shaft nut when removing it.
    4. Do not damage the threads of the driven sprocket.



    C270547E01
  1. Using SST, hold the front output shaft companion flange sub-assembly.

    SST
    09330-00021  

  1. Using a 32 mm socket wrench, remove the transfer output shaft nut.
    Text in Illustration 
    *a
    Hold
    *b
    Turn



    C180859
  1. Remove the O-ring.



    C270548E01
  1. Using SST, remove the front output shaft companion flange sub-assembly.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)
    Text in Illustration 
    *a
    Hold
    *b
    Turn



4. REMOVE TRANSFER CASE FRONT OIL SEAL


    C159300E01
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the oil seal and transfer front case contact surface.



5. INSTALL TRANSFER CASE FRONT OIL SEAL
  1. Apply transfer oil to the spline area of the output shaft.



    C159301E01
  1. Using SST and a hammer, tap in the oil seal until its surface is 1 to 1.5 mm (0.0394 to 0.0591 in.) from the case upper surface.

    SST
    09316-60011   (09316-00011)



6. INSTALL FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Install the front output shaft companion flange sub-assembly onto the driven sprocket.



    C270559E01
  1. Using SST to hold the front output shaft companion flange sub-assembly, install a new companion flange lock nut.

    SST
    09330-00021  

  1. Using a 32 mm socket wrench, install a new O-ring and a new transfer output shaft nut.

    Torque:
    127 N*m{ 1299 kgf*cm , 94 ft.*lbf }

    Text in Illustration 
    *a
    Hold
    *b
    Turn



    F050151E04
  1. Using a chisel and hammer, stake the transfer output shaft nut.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect



7. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
  1. Install the front propeller shaft (Click here).



8. ADD TRANSFER OIL
  1. Install a new gasket and the drain plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Pour oil so that the oil level is between 0 to 5.0 mm (0 to 0.197 in.) from the bottom lip of the filler plug hole.

    NOTICE:
    1. Pour oil slowly.
    2. Pour oil a little at a time, waiting several minutes between each addition of oil.

  1. Wait approximately 5 minutes and check that the oil level has not changed.

  1. Install a new gasket and the filler plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



    C159809
  1. Install the lower transfer case protector with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



9. CHECK TRANSFER OIL
  1. Remove the filler plug and gasket.



    C083746E08
  1. Check that the oil level is between 0 to 5.0 mm (0 to 0.197 in.) from the bottom lip of the filler plug hole.
    If the result is not as specified, add transfer oil.

    Oil grade:
    GL-4 or GL-5

    Viscosity:
    SAE 75W-90

    Standard capacity:
    1.1 +/- 0.06 liters (1.2 +/- 0.06 US qts, 1.0 +/- 0.05 Imp. qts)

    NOTICE:
    1. After changing the oil, drive the vehicle and check the oil level again.
    2. Too much or too little oil will lead to transfer problems.

  1. When the oil level is too low, check for oil leak.

  1. Install a new gasket into the filler plug and then tighten the plug.



10. CHECK FOR TRANSFER OIL LEAK