INTAKE MANIFOLD > REMOVAL |
| 1. DISCHARGE FUEL SYSTEM PRESSURE |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the fuel pump ECU connector (Click here).
Connect the cable to the negative (-) battery terminal.
Start the engine. After the engine has stopped on its own, turn the ignition switch OFF.
Crank the engine again, then check that the engine does not start.
Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.
Connect the fuel pump ECU connector (Click here).
| 2. REMOVE EGR VALVE ASSEMBLY |
Remove the EGR valve (Click here).
| 3. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY |
Remove the front wiper motor and link (Click here).
| 4. REMOVE COWL TOP OUTER PANEL SUB-ASSEMBLY |
Disconnect the washer hose and 2 wire harness clamps.
Remove the 7 bolts and outer panel.

| 5. REMOVE VENTILATION HOSE ASSEMBLY |
![]() |
Disconnect the ventilation hose from the ventilation pipe of the cylinder head cover LH and RH.
Remove the bolt and ventilation hose.
| 6. REMOVE AIR TUBE SUB-ASSEMBLY LH |
![]() |
Disconnect the 2 connectors.
Disconnect the water by-pass hose.
![]() |
Disconnect the 2 wire harness clamps and air hose.
Remove the bolt and disconnect the air tube LH from the water inlet housing.
![]() |
Disconnect the vacuum sensor connector and clamp.
Remove the 2 bolts and disconnect the air hose from the air switching valve LH.
Remove the air tube LH.
| 7. REMOVE INTAKE MANIFOLD |
![]() |
Disconnect the No. 4 water by-pass hose.
Disconnect the throttle body connector.
Disconnect the No. 1 ventilation hose.
![]() |
Disconnect the purge VSV connector.
Disconnect the purge line hose from the purge VSV.
Disconnect the vacuum switching valve connector (for ACIS).
![]() |
Disconnect the vacuum hose.
![]() |
Remove the bolt and disconnect the wire harness from the wire harness bracket.
Detach the 3 wire harness clamps from the 3 wire harness brackets.
![]() |
Detach the 4 clamps from the fuel tube.
![]() |
Disconnect the fuel tube from the fuel delivery pipe RH (Click here).
![]() |
Disconnect the fuel tube from the fuel delivery pipe LH (Click here).
![]() |
Remove the 2 nuts, 8 bolts, intake manifold and 2 gaskets.
| 8. REMOVE FUEL TUBE SUB-ASSEMBLY |
![]() |
Remove the bolt and fuel tube from the intake manifold.
| 9. REMOVE V-BANK COVER BRACKET |
![]() |
Remove the 2 bolts and bracket.
| 10. REMOVE V-BANK COVER PIN |
![]() |
Remove the pin from the intake manifold.
| 11. REMOVE STUD BOLT |
![]() |
Using an E5 "TORX" socket wrench, remove the 2 stud bolts.
| 12. REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS) |
![]() |
Disconnect the 2 vacuum hoses from the vacuum switching valve.
Remove the bolt and vacuum switching valve.
| 13. REMOVE PURGE VSV |
![]() |
Disconnect the purge line hose from the intake manifold.
Remove the bolt and purge VSV.
| 14. REMOVE UNION TO CONNECTOR TUBE HOSE ASSEMBLY |
![]() |
Remove the 2 bolts and detach the hose clamp.
Remove the union to connector tube hose from the intake manifold.
Remove the 2 bolts and 2 wire harness brackets.
| 15. REMOVE MANIFOLD ABSOLUTE PRESSURE SENSOR |
Disconnect the manifold absolute pressure sensor connector.
![]() |
Remove the screw and manifold absolute pressure sensor.
![]() |
Remove the O-ring from the manifold absolute pressure sensor.
| 16. REMOVE THROTTLE BODY ASSEMBLY |
![]() |
Remove the 4 bolts, throttle body and gasket.