ENGINE ASSEMBLY > INSTALLATION |
| 1. REMOVE ENGINE FROM ENGINE STAND |
![]() |
Install the 2 engine hangers with the 2 bolts as shown in the illustration.
| Engine hanger | 12281-38150 |
| Bolt | 90119-A0166 |
Attach an engine sling device and hang the engine with a chain block.
Remove the bolts and engine assembly from the engine stand.
| 2. INSTALL ENGINE ASSEMBLY |
Slowly lower the engine assembly into the engine compartment.
Attach the engine mounting insulators to the vehicle.
![]() |
Install the 4 engine mounting insulator bolts.
Remove the 2 bolts and 2 engine hangers.
| 3. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
![]() |
Using SST, hold the crankshaft.
![]() |
Install the crankshaft angle sensor rotor.
![]() |
Install the drive plate and rear drive plate spacer onto the crankshaft.
![]() |
Apply adhesive to 2 or 3 threads of the 8 bolts.
![]() |
Install and uniformly tighten 10 new bolts in the sequence shown in the illustration.
![]() |
Mark the top of each drive plate installation bolt with paint.
Tighten the drive plate installation bolts 90° as shown in the illustration.
Check that the painted marks are now at a 90° angle to the top.
| 4. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR (for 4WD) |
Install the rear engine mounting insulator to the transmission with the 4 bolts.
| 5. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR (for 2WD) |
Install the rear engine mounting insulator to the transmission with the 4 bolts.
| 6. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY |
for 2WD:
Refer to the following procedures (Click here).
for 4WD:
Refer to the following procedures (Click here).
| 7. INSTALL STARTER ASSEMBLY |
Install the flywheel housing side cover.
Install the starter with the 2 bolts.
Connect the starter wire with the nut.
Connect the starter connector.
Attach the 2 wire harness clamps.
| 8. INSTALL STARTER COVER |
Install the starter cover with the 3 bolts.
| 9. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH |
![]() |
Install a new gasket to the cylinder head and a new gasket to the No. 3 air tube.
![]() |
Temporarily install the exhaust manifold with 9 new nuts, and then uniformly tighten the 7 nuts that are not labeled A. Then tighten the 2 nuts labeled A in the illustration.
| 10. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Install the heat insulator with the 3 bolts.
| 11. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH |
![]() |
Install a new gasket to the cylinder head and a new gasket to the No. 4 air tube.
![]() |
Temporarily install the exhaust manifold with 9 new nuts, and then uniformly tighten the 7 nuts that are not labeled A. Then tighten the 2 nuts labeled A in the illustration.
| 12. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Install the heat insulator with the 3 bolts.
| 13. INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY |
Install 2 new gaskets.
![]() |
Install the EGR pipe with the 4 nuts, and tighten the nuts in the sequence shown in the illustration.
| 14. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE |
Apply a light coat of engine oil to a new O-ring.
Install the O-ring to the dipstick guide.
![]() |
Install the dipstick guide with the bolt.
Install the dipstick.
| 15. CONNECT NO. 1 WATER BY-PASS PIPE |
![]() |
Connect the No. 1 water by-pass pipe with the 3 bolts.
| 16. INSTALL EXHAUST PIPE ASSEMBLY |
for Regular Cab Standard Deck:
Refer to the following procedures (Click here).
except Regular Cab Standard Deck:
Refer to the following procedures (Click here).
| 17. INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD) |
Install the front propeller shaft (Click here).
| 18. INSTALL PROPELLER SHAFT ASSEMBLY |
for 2WD:
Refer to the following procedures (Click here).
for 4WD:
Refer to the following procedures (Click here).
| 19. INSTALL GENERATOR ASSEMBLY |
![]() |
Install the generator with the 3 bolts and nut.
![]() |
Install the harness bracket to the generator with the bolt.
Connect the generator connector.
Connect the generator wire with the nut.
Install the terminal cap.
| 20. CONNECT OIL COOLER TUBE SUB-ASSEMBLY (w/ Trailer Towing System) |
![]() |
Connect the oil cooler tube with the 2 bolts.
| 21. CONNECT VANE PUMP ASSEMBLY |
![]() |
![]() |
Connect the vane pump to the timing chain cover with the 2 bolts.
| 22. CONNECT COOLER COMPRESSOR ASSEMBLY |
![]() |
Connect the cooler compressor with the 2 stud bolts.
Install the 2 bolts and 2 nuts.
| 23. CONNECT WIRE HARNESS AND HOSE |
![]() |
Connect the 2 connectors and 2 clips to the engine room junction block.
Install the engine wire with the nut. Then connect the 2 clips.
Connect the 4 air injection control driver connectors.
Install the ground wire with the bolt.
Connect the cable to the positive (+) battery terminal.
Install the wire to the positive (+) battery cable with the nut.
![]() |
Connect the air injection system hose.
Install the connector bracket with the nut.
Connect the 2 clamps and air pump connector.
Connect the clamp and ground wire with the bolt.
![]() |
Connect the 4 connectors to the connector holder block.
![]() |
Connect the 2 heater hoses.
![]() |
Connect the No. 4 water by-pass hose.
![]() |
Connect the ECM connector and clamp.
| 24. CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY |
![]() |
Connect the No. 2 fuel tube (Click here).
| 25. CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY |
![]() |
Connect the No. 1 fuel pipe (Click here).
Install the fuel pipe clamp.
| 26. INSTALL INTAKE MANIFOLD |
![]() |
Place 2 new gaskets on the intake manifold.
Place the intake manifold on the cylinder head.
![]() |
Install and uniformly tighten the 8 bolts and 2 nuts in several steps.
![]() |
Connect the fuel tube to the fuel delivery pipe LH (Click here).
![]() |
Connect the fuel tube to the fuel delivery pipe RH (Click here).
![]() |
Attach the 4 clamps to the fuel tube as shown in the illustration.
![]() |
Attach the 3 wire harness clamps to the 3 wire harness brackets.
Connect the wire harness to the wire harness bracket with the bolt.
![]() |
Connect the vacuum hose.
![]() |
Connect the purge VSV connector.
Connect the purge line hose to the purge VSV.
Connect the vacuum switching valve connector (for ACIS).
![]() |
Connect the No. 1 ventilation hose.
Connect the No. 4 water by-pass hose.
Connect the throttle body connector.
| 27. INSTALL AIR TUBE SUB-ASSEMBLY LH |
![]() |
Connect the air hose to the air switching valve LH, and install the air tube LH with the 2 bolts.
Connect the vacuum sensor connector and clamp.
![]() |
Connect the air tube LH to the water inlet housing with the bolt.
Connect the air hose.
Connect the 2 wire harness clamps.
![]() |
Connect the water by-pass hose and 2 connectors.
| 28. INSTALL VENTILATION HOSE ASSEMBLY |
![]() |
Install the ventilation hose with the bolt.
Connect the ventilation hose to the ventilation pipe of the cylinder head cover LH and RH.
| 29. INSTALL EGR VALVE BRACKET |
![]() |
Install the EGR valve bracket with the 3 bolts.
| 30. INSTALL EGR VALVE ASSEMBLY |
![]() |
Install a new gasket to the intake manifold.
![]() |
Install a new gasket to the No. 2 EGR pipe.
![]() |
Temporarily install the EGR valve assembly to the intake manifold with the 2 bolts and 4 nuts.
![]() |
Using several steps, uniformly tighten the 2 bolts and 4 nuts in the sequence shown in the illustration.
| 31. CONNECT NO. 13 WATER BY-PASS HOSE |
![]() |
Connect the No. 13 water by-pass hose.
| 32. CONNECT NO. 12 WATER BY-PASS HOSE |
![]() |
Connect the No. 12 water by-pass hose.
| 33. INSTALL RADIATOR ASSEMBLY |
Install a new O-ring to the drain cock plug.
Install the drain cock plug.
![]() |
Install the outlet radiator hose into the radiator.
![]() |
Set the radiator bracket hooks to the radiator support holes.
Install the radiator with the 4 bolts.
| 34. INSTALL FAN SHROUD |
Install the fan pulley to the fan bracket.
Place the fan shroud together with the fluid coupling fan between the radiator and engine.
Temporarily install the fluid coupling fan to the fan bracket with the 4 nuts. Tighten the nuts as much as possible by hand.
![]() |
Attach the shroud's claws to the radiator as shown in the illustration.
Install the shroud with the 2 bolts.
![]() |
w/ Trailer Towing System:
Pass the 2 hoses through the flexible hose clamp and close the clamp as shown in the illustration.
Connect the reservoir hose to the upper radiator tank.
Install the fan and generator V-belt (Click here).
![]() |
Tighten the 4 nuts of the fluid coupling fan.
| 35. INSTALL FAN AND GENERATOR V BELT |
![]() |
Set the V belt onto every part.
While turning the belt tensioner counterclockwise, remove the pin.
![]() |
After installing the belt, check that it fits properly in the ribbed grooves.
| 36. INSTALL RADIATOR SIDE DEFLECTOR LH |
![]() |
Install the deflector with the 6 clips.
Connect the wire harness clamp.
| 37. INSTALL RADIATOR SIDE DEFLECTOR RH |
![]() |
Install the deflector with the 6 clips.
| 38. CONNECT OUTLET RADIATOR HOSE |
![]() |
Connect the radiator hose.
| 39. INSTALL INLET RADIATOR HOSE |
![]() |
Install the inlet radiator hose.
| 40. INSTALL FRONT FENDER APRON SEAL REAR LH |
Install the fender apron seal with the 5 clips.
| 41. INSTALL FRONT FENDER APRON SEAL LH |
Install the fender apron seal with the 6 clips.
| 42. INSTALL FRONT FENDER APRON SEAL REAR RH |
Install the fender apron seal with the 5 clips.
| 43. INSTALL FRONT FENDER APRON SEAL RH |
Install the fender apron seal with the 6 clips.
| 44. INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY |
Install the outer panel with the 7 bolts.

Connect the washer hose.
Connect the 2 wire harness clamps.
| 45. INSTALL AIR CLEANER ASSEMBLY |
![]() |
Install the air cleaner case with the 2 bolts.
Install the air cleaner element to the air cleaner case.
![]() |
Install the air cleaner cap.
Install the air cleaner cap and fasten the 4 hook clamps.
Connect the MAF meter connector.
Attach the wire harness clamp.
| 46. INSTALL AIR CLEANER HOSE ASSEMBLY |
![]() |
Install the air cleaner hose with the 2 clamps.
Connect the ventilation hose and vacuum sensing hose.
| 47. ADD ENGINE OIL |
Add fresh oil.
| Oil Grade | Oil Viscosity (SAE) |
| ILSAC GF-5 multigrade engine oil | 0W-20 |
| Item | Specified Condition |
| Drain and refill without oil filter change | 7.1 liters (7.5 US qts, 6.2 Imp. qts) |
| Drain and refill with oil filter change | 7.5 liters (7.9 US qts, 6.6 Imp. qts) |
| Dry fill | 9.3 liters (9.8 US qts, 8.2 Imp. qts) |
Install the oil filler cap.
| 48. ADD ENGINE COOLANT |
Add engine coolant.
| Item | Specified Condition |
| w/ Trailer Towing System | 13.2 liters (13.9 US qts, 11.6 Imp. qts) |
| w/o Trailer Towing System | 12.1 liters (12.8 US qts, 10.6 Imp. qts) |
![]() |
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
Install the radiator cap.
Start the engine and warm it up until the thermostat opens.
Maintain the engine speed at 2000 to 2500 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines.
If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 49. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 50. INSPECT FOR OIL LEAK |
Start the engine. Make sure that there are no oil leaks from the area that was worked on.
| 51. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 52. INSPECT FOR EXHAUST GAS LEAK |
| 53. INSPECT FOR FUEL LEAK |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and Techstream main switch ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.
| 54. INSPECT SHIFT LEVER POSITION |
for Column Shift:
Refer to the following procedures .
for Floor Shift:
Refer to the following procedures .
| 55. INSTALL V-BANK COVER SUB-ASSEMBLY |
![]() |
Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.
| 56. INSTALL HOOD SUB-ASSEMBLY |
![]() |
Install the hood with the 4 bolts.
Attach the lower part of the 2 hood supports to the hood support bolt ball joints.
Attach the hood support clips.
| 57. ADJUST HOOD SUB-ASSEMBLY |
![]() |
Adjust the hood's position.
Loosen the hood's 4 hinge bolts.
Move the hood and adjust the clearance between the hood and front fender.
Tighten the hood's 4 hinge bolts after the adjustment.
![]() |
Adjust the cushion rubber so that the height of the hood and fender are aligned.
Adjust the hood lock.
![]() |
Using a screwdriver, remove the hood lock nut cap as shown in the illustration.
![]() |
Loosen the 2 bolts and hood lock nut.
Adjust the hood lock position so that the striker can enter it smoothly.
Tighten the bolts and nut after the adjustment.
Install a new cap.
| 58. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Hook the engine under cover to the vehicle body as shown in the illustration.
Install the 3 screws and 5 bolts.
| 59. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY |
Install the front wiper motor and link (Click here).
| 60. INSPECT IGNITION TIMING |
Warm up and stop the engine.
Allow the engine to warm up to a normal operating temperature.
When using the Techstream:
Connect the Techstream to the DLC3.
Start the engine and idle it.
Turn the Techstream main switch ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / IGN Advance.
Disconnect the Techstream from the DLC3.
![]() |
When not using the Techstream:
Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
![]() |
Using the timing light, check the ignition timing.
Remove SST from the DLC3.
Check the ignition timing.
Disconnect the timing light from the engine.
| 61. INSPECT ENGINE IDLE SPEED |
Warm up and stop the engine.
Allow the engine to warm up to a normal operating temperature.
When using the Techstream:
Connect the Techstream to the DLC3.
Race the engine at 2500 rpm for approximately 90 seconds.
Turn the Techstream main switch ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.
Disconnect the Techstream from the DLC3.
![]() |
When not using the Techstream:
Using SST, connect the tachometer probe to terminal 9 (TAC) of the DLC3.
Race the engine at 2500 rpm for approximately 90 seconds.
Check the idle speed.
Disconnect the tachometer probe from the DLC3.
| 62. INSPECT CO/HC |
Start the engine.
Keep the engine speed at 2500 rpm for approximately 180 seconds.
![]() |
Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.
Immediately check CO/HC concentration at idle and/or 2500 rpm.
If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.
Check the A/F sensor operation (Click here) and heated oxygen sensor operation (Click here).
See the table below for possible causes, and then inspect and correct the applicable causes if necessary.
| CO | HC | Symptom | Cause |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (Fluctuating HC reading) |
|
| High | High | Rough idle (Black smoke from exhaust) |
|
| 63. CHECK ENGINE OIL LEVEL |
Warm up the engine, then stop the engine and wait for 5 minutes.
Check that the engine oil level is between the low level and full level marks on the dipstick.
If low, check for leakage and add oil up to the full level mark.
| 64. CHECK ENGINE COOLANT LEVEL |
![]() |
Check that the engine coolant level is between the LOW and FULL lines when the engine is cold.
If the engine coolant is low, check for leaks and add "TOYOTA Super Long Life Coolant" or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology to the FULL line.