SFI SYSTEM > Fuel Injector Circuit |

| 1.CHECK INJECTOR ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the injector connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Cylinder | Tester Connection | Switch Condition | Specified Condition |
| No. 1 | H1-2 - Ground | Ignition switch ON | 11 to 14 V |
| No. 2 | F1-2 - Ground | Ignition switch ON | 11 to 14 V |
| No. 3 | H2-2 - Ground | Ignition switch ON | 11 to 14 V |
| No. 4 | F2-2 - Ground | Ignition switch ON | 11 to 14 V |
| No. 5 | H3-2 - Ground | Ignition switch ON | 11 to 14 V |
| No. 6 | F3-2 - Ground | Ignition switch ON | 11 to 14 V |
| No. 7 | H4-2 - Ground | Ignition switch ON | 11 to 14 V |
| No. 8 | F4-2 - Ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 2.INSPECT INJECTOR ASSEMBLY |
Inspect the injector .
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM) |
Disconnect the injector connector.
Disconnect the D74 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Cylinder | Tester Connection | Condition | Specified Condition |
| No. 1 | H1-1 - Body ground | Always | 10 kΩ or higher |
| H1-1 - D74-86 (#10) | Always | Below 1 Ω | |
| No. 2 | F1-1 - Ground | Always | 10 kΩ or higher |
| F1-1 - D74-109 (#20) | Always | Below 1 Ω | |
| No. 3 | H2-1 - Ground | Always | 10 kΩ or higher |
| H2-1 - D74-85 (#30) | Always | Below 1 Ω | |
| No. 4 | F2-1 - Ground | Always | 10 kΩ or higher |
| F2-1 - D74-108 (#40) | Always | Below 1 Ω | |
| No. 5 | H3-1 - Ground | Always | 10 kΩ or higher |
| H3-1 - D74-84 (#50) | Always | Below 1 Ω | |
| No. 6 | F3-1 - Ground | Always | 10 kΩ or higher |
| F3-1 - D74-107 (#60) | Always | Below 1 Ω | |
| No. 7 | H4-1 - Ground | Always | 10 kΩ or higher |
| H4-1 - D74-83 (#70) | Always | Below 1 Ω | |
| No. 8 | F4-1 - Ground | Always | 10 kΩ or higher |
| F4-1 - D74-106 (#80) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 4.INSPECT FUSE (INJ, IG2 MAIN) |
![]() |
Remove the INJ fuse and IG2 MAIN fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| INJ fuse | Always | Below 1 Ω |
| IG2 MAIN fuse | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.INSPECT INTEGRATION RELAY (IG2) |
Inspect the integration relay (Click here).
|
| ||||
| OK | ||
| ||