DTC P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) |
DTC P0019 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0017 | Deviations in the crankshaft position sensor and VVT sensor 1 (for exhaust camshaft) signals (2 trip detection logic). |
|
| P0019 | Deviations in the crankshaft position sensor and VVT sensor 2 (for exhaust camshaft) signals (2 trip detection logic). |
| Related DTCs | P0017: Camshaft timing misalignment at idling (Bank 1 Exhaust Side) P0019: Camshaft timing misalignment at idling (Bank 2 Exhaust Side) |
| Required Sensors/Components (Main) | Camshaft timing exhaust gear assembly |
| Required Sensors/Components (Related) | VVT sensor, Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | Less than 60 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not stored | P0013, P0023 (Exhaust VVT Oil Control Valve) P0017, P0019 (Exhaust VVT System - Misalignment) P0102, P0103 (Mass Air Flow Sensor) P0115, P0117, P0118 (Engine Coolant Temperature Sensor) P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control) P0335 (Crankshaft Position Sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) |
| Engine speed | 500 to 1000 rpm |
| One of the following conditions is met: | Condition 1 or 2 |
| 1. VVT learned value at maximum advanced valve timing | Less than 81.1°CA |
| 2. VVT learned value at maximum advanced valve timing | More than 105.9°CA |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0017 OR P0019) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P0017 or P0019 is output | A |
| P0017 or P0019 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY FOR EXHAUST SIDE) |
Connect the Techstream to the DLC3.
Start the engine and turn the Techstream on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2).
Perform the Active Test. Check that the displacement angle varies.
|
| ||||
| OK | |
| 3.ADJUST VALVE TIMING |
Adjust the valve timing (Click here).
|
| ||||
| 4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE) |
Inspect the camshaft timing oil control valve assembly (for exhaust side) (Click here).
|
| ||||
| OK | |
| 5.CHECK OIL CONTROL VALVE FILTER AND OIL PIPE |
![]() |
Remove the No. 1 or No. 2 oil pipe.
Remove the oil control valve filter.
Check that the filter and pipe are not clogged.
| *1 | No. 1 Oil Pipe |
| *2 | No. 2 Oil Pipe |
|
| ||||
| OK | |
| 6.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
Replace the camshaft timing exhaust gear assembly (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0017 OR P0019) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (Click here).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Read the output pending DTCs using the Techstream.
|
| ||||
| OK | ||
| ||