DTC P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) |
DTC P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) |
DTC P0018 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A) |
DTC P0019 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B) |
| DTC Code | DTC Detection Condition | Trouble Area |
| P0016 | Deviation in crankshaft position sensor signal and VVT sensor 1 (for Intake Camshaft Bank 1) signal (2 trip detection logic) |
|
| P0017 | Deviation in crankshaft position sensor signal and VVT sensor 1 (for Exhaust Camshaft Bank 1) signal (2 trip detection logic) |
|
| P0018 | Deviation in crankshaft position sensor signal and VVT sensor 2 (for Intake Camshaft Bank 2) signal (2 trip detection logic) |
|
| P0019 | Deviation in crankshaft position sensor signal and VVT sensor 2 (for Exhaust Camshaft Bank 2) signal (2 trip detection logic) |
|
| Related DTCs | P0016: Camshaft timing misalignment at idling (Bank 1 Intake Side) P0017: Camshaft timing misalignment at idling (Bank 1 Exhaust Side) P0018: Camshaft timing misalignment at idling (Bank 2 Intake Side) P0019: Camshaft timing misalignment at idling (Bank 2 Exhaust Side) |
| Required Sensors/Components (Main) | VVT actuator |
| Required Sensors/Components (Related) | Camshaft position sensor, Crankshaft position sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | Within 1 minute |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0010, P0020 (VVT Oil control valve) P0016, P0018 (VVT System) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0335 (Crankshaft position sensor) P1340 (Camshaft position sensor) |
| Engine RPM | 400 to 1400 rpm |
| Monitor runs whenever following DTCs not present | P0013, P0023 (Exhaust VVT Oil control valve) P0017, P0019 (Exhaust VVT System - Misalignment) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0335 (Crankshaft position sensor) P1340 (Camshaft position sensor) |
| Engine RPM | 400 to 1400 rpm |
| One of following conditions met | - |
| VVT learning value at maximum retarded valve timing | Less than 22.23°CA |
| VVT learning value at maximum retarded valve timing | More than 46.68°CA |
| One of following conditions met | - |
| VVT learning value at maximum advanced valve timing | Less than 82.23°CA |
| VVT learning value at maximum advanced valve timing | More than 106.68°CA |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016, P0017, P0018 OR P0019) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P0016, P0017, P0018 or P0019 is output | A |
| P0016, P0017, P0018 or P0019 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV) |
Connect the Techstream to the DLC3.
Start the engine and turn the Techstream on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2) or Control the VVT Exhaust Linear (Bank 1) or Control the Exhaust VVT Linear (Bank 2) / All Data / VVT Change Angle #1, VVT Change Angle #2, VVT Ex Chg Angle #1, VVT Ex Chg Angle #2.
Perform the Active Test. Check that the displacement angle varies.
|
| ||||
| OK | |
| 3.ADJUST VALVE TIMING |
Adjust the valve timing (Click here).
|
| ||||
| 4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
Inspect the camshaft oil control valve assembly (Click here).
|
| ||||
| OK | |
| 5.REPLACE CAMSHAFT TIMING GEAR |
Replace the camshaft timing gear (Click here).
| NEXT | |
| 6.CONFIRM WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTC (Click here).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Read the output pending DTCs using the Techstream.
|
| ||||
| OK | ||
| ||