DTC P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2121 | Either conditions (1) or (2) met for 0.5 seconds (1 trip detection logic):
|
|
| Related DTCs | P2121: Accelerator pedal position sensor rationality |
| Required Sensors/Components (Main) | Accelerator pedal sensor assembly |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | P2120, P2122, P2123, P2125, P2127, P2128, P2138 (Accelerator pedal position sensor) |
| Either of following conditions 1 or 2 met: | - |
| 1. Ignition switch | ON |
| 2. Throttle actuator power | ON |
| VPA2 voltage | Less than 4.84 V |
| Either of following conditions met: | a or b |
| a) VPA voltage - Learned VPA accelerator off position voltage | 0.04 V or more |
| b) VPA2 voltage - Learned VPA2 accelerator off position voltage | 0.04 V or more |
| Difference between VPA voltage and VPA2 voltage (learned value of accelerator off position) | Less than 0.4 V, or more than 1.2 V |
| (VPA voltage - Learned VPA accelerator off position voltage) - (VPA2 voltage - Learned VPA2 accelerator off position voltage) | 0.165 V or more (varies with accelerator position) |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2121) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P2121 is output | A |
| P2121 and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (ACCELERATOR PEDAL POSITION SENSOR) |
![]() |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.
Read the values displayed on the Techstream.
| Accelerator Pedal Operation | Accel Sensor Out No. 1 | Accel Sensor Out No. 2 |
| Released | 0.5 to 1.1 V | 1.2 to 2.0 V |
| Depressed | 2.6 to 4.5 V | 3.4 to 4.7 V |
|
| ||||
| OK | ||
| ||
| 3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY |
Replace the accelerator pedal sensor assembly (Click here).
| NEXT | |
| 4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P2121 is output | A |
| No DTC is output | B |
|
| ||||
| A | ||
| ||