Home › ENGINE ยท 1UR-FE › FUEL › FUEL INJECTOR

FUEL INJECTOR > INSTALLATION

for Preparation Click here


HINT:
Perform "Inspection After Repairs" after replacing the fuel injector (Click here).



1. INSTALL FUEL INJECTOR ASSEMBLY

HINT:
Perform "Inspection After Repairs" after replacing the fuel injector (Click here).



    A214317
  1. Attach the 3 clamps to install the No. 6 wire harness to the fuel delivery pipe sub-assembly RH.



    A214318
  1. Attach the 3 clamps to install the No. 7 wire harness to the fuel delivery pipe sub-assembly LH.



    A149190E01
  1. Apply gasoline or spindle oil to a new O-ring and install it to the fuel injector assembly.

    NOTICE:
    Make sure that there is no damage or foreign material in the groove of the fuel injector assembly when installing the O-ring.



    A161427E01
  1. Connect the injector connector.



    A161479E01
  1. Install the fuel injector assembly to the fuel delivery pipe sub-assembly as shown in the illustration.

    NOTICE:
    1. Make sure that there are no scratches or foreign matter in or around the insertion hole of the fuel delivery pipe sub-assembly.
    2. When inserting the fuel injector assembly, be careful not to damage the O-ring.
    3. Attach the part of the fuel injector labeled B between the parts of the fuel delivery pipe labeled A.



    A214319E05
  1. Check that each fuel injector assembly is installed to the fuel delivery pipe sub-assembly facing the direction shown in the illustration.



2. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY LH


    A214316
  1. Install the 2 delivery pipe spacers and 4 insulators to the cylinder head sub-assembly LH.

  1. Install the fuel delivery pipe sub-assembly LH (with injectors) to the cylinder head sub-assembly LH.



  1. Install the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


    NOTICE:
    A163659E08
    Make sure that the part of the fuel injector labeled B is between the parts of the fuel delivery pipe labeled A.

  1. Connect the No. 7 wire harness connector.



3. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY RH


    A214315
  1. Install the 2 delivery pipe spacers and 4 insulators to the cylinder head sub-assembly RH.

  1. Install the fuel delivery pipe sub-assembly RH (with injectors) to the cylinder head sub-assembly RH.



  1. Install the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


    NOTICE:
    A163659E09
    Make sure that the part of the fuel injector labeled B is between the parts of the fuel delivery pipe labeled A.

  1. Connect the No. 6 wire harness connector.



4. CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY


    A308873
  1. Connect the No. 1 fuel pipe sub-assembly to the fuel delivery pipe sub-assembly LH (for Quick Type B) (Click here).

  1. Attach the clamp.



5. CONNECT FUEL TUBE SUB-ASSEMBLY


    A214312
  1. Connect the fuel tube sub-assembly to the fuel delivery pipe sub-assembly LH (for Quick Type A) (Click here).



    A214311
  1. Connect the fuel tube sub-assembly to the fuel delivery pipe sub-assembly RH (for Quick Type A) (Click here).



6. CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY


    A214310
  1. Connect the No. 2 fuel tube sub-assembly to the fuel pressure regulator assembly (for Quick Type A) (Click here).



7. INSTALL EGR VALVE BRACKET
(Click here)


8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


9. CHECK FOR FUEL LEAK
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and Techstream main switch on.

    NOTICE:
    Do not start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.