Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0125    Insufficient Coolant Temperature for Closed Loop Fuel Control

for Preparation Click here


DESCRIPTION

  1. Refer to DTC P0115 .

    DTC No.
    DTC Detection Condition
    Trouble Area
    P0125
    Engine coolant temperature does not reach the closed-loop enabling temperature for 20 minutes (this period varies with the engine coolant temperature at engine start) (2 trip detection logic).
    1. Engine coolant temperature sensor
    2. Cooling system
    3. Water inlet with thermostat

MONITOR DESCRIPTION

The resistance of the engine coolant temperature sensor varies in proportion to the actual engine coolant temperature. The ECM supplies a constant voltage to the sensor and monitors the output signal voltage of the sensor. The output signal voltage varies according to the resistance of the sensor. After the engine is started, the engine coolant temperature is monitored through this signal. If the engine coolant temperature sensor indicates that the engine is not yet warm enough for closed-loop fuel control despite a specified period of time having elapsed since the engine was started, the ECM interprets this as a malfunction in the sensor or cooling system and stores the DTC.
Example:
The engine coolant temperature is 0°C (32°F) at engine start. After approximately 1 minute of running time, the engine coolant temperature sensor still indicates that the engine is not warm enough to begin closed-loop fuel (air-fuel ratio feedback) control. The ECM interprets this as a malfunction in the sensor or cooling system and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0125: Insufficient engine coolant temperature for closed-loop fuel control
Required Sensors/Components (Main)
Water inlet with thermostat, cooling system
Required Sensors/Components (Related)
Engine coolant temperature sensor and mass air flow meter
Frequency of Operation
Once per driving cycle
Duration
63 seconds or more: Engine coolant temperature at engine start -3.33°C (26°F) or higher
127 seconds or more: Engine coolant temperature at engine start -14.44°C to -3.33°C (6°F to 26°F)
20 minutes or more: Engine coolant temperature at engine start below -14.44°C (6°F)
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not stored
P0101, P0102, P0103 (Mass Air Flow Sensor)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0128 (Thermostat)

TYPICAL MALFUNCTION THRESHOLDS


Engine coolant temperature (closed-loop fuel control enabling temperature)
Below 5°C (41°F)

CONFIRMATION DRIVING PATTERN

  1. Leave the vehicle outside overnight.
  2. Connect the Techstream to the DLC3.
  3. Turn the ignition switch to ON and turn the Techstream on.
  4. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
  5. Check that the engine coolant temperature is 5°C (41°F) or less.
  6. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  7. Turn the ignition switch off and wait for at least 30 seconds.
  8. Turn the ignition switch to ON and turn the Techstream on.
  9. Start the engine.
  10. Wait 21 minutes or more.
  11. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  12. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  13. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  14. Input the DTC: P0125.
  15. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
  16. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

HINT:
  1. If DTC P0115, P0116, P0117 or P0118 is stored simultaneously with DTC P0125, the engine coolant temperature sensor may have an open or short circuit. Troubleshoot those DTCs first.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0125)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0125 is output
    A
    P0125 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0125 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT WATER INLET WITH THERMOSTAT
  1. Remove the water inlet with thermostat (Click here).

  1. Check the valve opening temperature of the thermostat.

    Standard value:
    80 to 84°C (176 to 183°F)

    HINT:
    In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.

  1. Reinstall the water inlet with thermostat (Click here).



NG
REPLACE WATER INLET WITH THERMOSTAT (Click here)
OK


3.CHECK COOLING SYSTEM
  1. Check for defects in the cooling system that might cause the system to be too cold, such as abnormal radiator fan operation or any modifications.

    HINT:
    Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
REPAIR OR REPLACE COOLING SYSTEM
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)