DTC P0335 Crankshaft Position Sensor "A" Circuit |
DTC P0339 Crankshaft Position Sensor "A" Circuit Intermittent |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0335 | Either condition is met:
|
|
| P0339 | Under conditions (a), (b) and (c), no crankshaft position sensor signal is sent to the ECM for 0.05 seconds or more (1 trip detection logic): (a) Engine speed is 1000 rpm or more. (b) Starter signal is off. (c) 3 seconds or more have elapsed since the starter signal switched from on to off. |
|
![]() |
| Item | Content |
| Terminal | VV1+ - VV1- VV2+ - VV2- NE+ - NE- |
| Equipment Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Cranking or idling |
| Related DTCs | P0335: Crankshaft position sensor range check/rationality P0335: Crankshaft position sensor verify pulse input |
| Required Sensors/Components (Main) | Crankshaft position sensor |
| Required Sensors/Components (Related) | VVT sensor |
| Frequency of Operation | Continuous |
| Duration | -: Verify pulse input case 1 4.7 seconds: Verify pulse input case 2 0.016 seconds: Range check/rationality |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Engine speed signal | Signal input |
| Ignition switch | ON |
| Time after starter off to ON | 3 seconds or more |
| Number of VVT sensor signal pulses | 6 times |
| Battery voltage | 7 V or more |
| Minimum battery voltage while starter ON | Less than 11 V |
| VVT sensor circuit (P0340, P0342, P0343) | Not detected |
| Starter | OFF |
| Engine speed (Top dead center) | 600 rpm or more |
| Engine speed (30°CA) | 600 rpm or more |
| Time after starter ON to OFF | 3 seconds or more |
| Starter | ON |
| Minimum battery voltage while starter ON | Less than 11 V |
| Number of crankshaft position sensor signal pulses | 132 or less, or 174 or more |
| Engine speed signal | No signal |
| Crankshaft position sensor |
|
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE) |
Inspect the crankshaft position sensor .
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D4-1 - D74-110 (NE+) | Always | Below 1 Ω |
| D4-2 - D74-111 (NE-) | Always | Below 1 Ω |
| D4-1 or D74-110 (NE+) - Body ground | Always | 10 kΩ or higher |
| D4-2 or D74-111 (NE-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR) |
![]() |
Check the crankshaft position sensor installation.
|
| ||||
| OK | |
| 4.INSPECT CRANKSHAFT (TEETH OF CRANK ANGLE SENSOR PLATE) |
Check the teeth of the crank angle sensor plate
|
| ||||
| OK | ||
| ||