DTC P1340 Camshaft Position Sensor "A" (Bank 1 Sensor 2) |
DTC P1342 Camshaft Position Sensor "A" Low Input (MRE) |
DTC P1343 Camshaft Position Sensor "A" High Input (MRE) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P1340 | No camshaft position sensor signal to ECM during cranking (2 trip detection logic) |
|
| No camshaft position sensor signal to ECM with engine speed 600 rpm or more (1 trip detection logic) | ||
| P1342 | Output voltage of camshaft position sensor less than 0.3 V for 4 seconds (1 trip detection logic) | |
| P1343 | Output voltage of camshaft position sensor more than 4.7 V for 4 seconds (1 trip detection logic) |
| Related DTCs | P1340: Camshaft position sensor verify pulse input P1340: Camshaft position / Crankshaft position misalignment P1342: Camshaft position sensor range check (low voltage) P1343: Camshaft position sensor range check (high voltage) |
| Required Sensors/Components (Main) | Camshaft position sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor, Engine speed sensor |
| Frequency of Operation | Continuous |
| Duration | 4 seconds: P1340 camshaft position sensor verify pulse input P1342: Camshaft position sensor range check (low voltage) P1343: Camshaft position sensor range check (high voltage) 5 seconds: P1340 camshaft position / crankshaft position misalignment |
| MIL Operation | 2 driving cycles: P1340 camshaft position sensor verify pulse input Immediate: P1340 camshaft position / crankshaft position misalignment and P1342, P1343 camshaft position sensor range check |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Starter | ON (Not including when starter turned ON multiple times) |
| Minimum battery voltage while starter ON | Less than 11 V |
| Monitor runs whenever following DTCs not present | P0342, P0343 (VVT sensor) P1342, P1343 (Camshaft position sensor) |
| Engine RPM | 600 rpm or more |
| Starter | OFF |
| Camshaft position sensor range | 0.3 to 4.7 V |
| Monitor runs whenever following DTCs not present | P0340 (VVT sensor) P1340 (Camshaft position sensor) |
| Time after ignition switch off to ON | 2 seconds or more |
| Battery voltage | 8 V or more |
| Starter | OFF |
| Camshaft position signal | No signal |
| Camshaft position and crankshaft position phase | Misaligned |
| Camshaft position sensor voltage | Less than 0.3 V |
| Camshaft position sensor voltage | More than 4.7 V |
| Camshaft position sensor signal |
|
| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.INSPECT CAMSHAFT POSITION SENSOR (SENSOR POWER SOURCE) |
![]() |
Disconnect the camshaft position sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D6-3 (VC) - Body ground | Ignition switch ON | 4.5 to 5.0 V |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (ECM - CAMSHAFT POSITION SENSOR) |
![]() |
Disconnect the camshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D6-1 (G2) - D74-90 (G2) | Always | Below 1 Ω |
| D6-2 (G-) - D74-89 (G2-) | Always | Below 1 Ω |
| D6-1 (G2) or D74-90 (G2) - Body ground | Always | 10 kΩ or higher |
| D6-2 (G-) or D74-89 (G2-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION |
![]() |
Check the camshaft position sensor installation.
|
| ||||
| OK | |
| 4.INSPECT CAMSHAFT TIMING PLATE (SENSOR PLATE TOOTH) |
Check the teeth of the sensor plate.
|
| ||||
| OK | |
| 5.REPLACE CAMSHAFT POSITION SENSOR |
Replace the camshaft position sensor (Click here).
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Read DTCs.
| Result | Proceed to |
| No DTC is output | A |
| P1340, P1342 and/or P1343 is output | B |
|
| ||||
| A | ||
| ||