Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0031    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)

DTC    P0032    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)

DTC    P0051    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)

DTC    P0052    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)

DTC    P101D    A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON

DTC    P103D    A/F Sensor Heater Circuit Performance Bank 2 Sensor 1 Stuck ON

for Preparation Click here


DESCRIPTION

Refer to DTC P2195 .

HINT:
  1. Although the DTC titles say heated oxygen sensor, these DTCs relate to the air fuel ratio sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-way Catalytic Converter (TWC) and located near the engine assembly.
  3. When one of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

  4. The ECM provides a pulse-width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.


    A160615E12


DTC No.
DTC Detection Condition
Trouble Area
P0031
P0051
Air fuel ratio sensor heater current is below 0.8 A (1 trip detection logic).
  1. Open in air fuel ratio sensor heater circuit
  2. Air fuel ratio sensor heater (sensor 1)
  3. No. 1 integration relay
  4. ECM
P0032
P0052
Air fuel ratio sensor heater current failure (1 trip detection logic).
  1. Short in air fuel ratio sensor heater circuit
  2. Air fuel ratio sensor heater (sensor 1)
  3. No. 1 integration relay
  4. ECM
P101D
P103D
The heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
  1. Open or short in air fuel ratio sensor heater circuit
  2. ECM

MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor to regulate the air-fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the Three-way Catalytic Converter (TWC) to purify the exhaust gases.
The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum coated zirconia and includes an integrated heating element.
The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.
The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate. As a result, the ECM is unable to regulate the air-fuel ratio properly.
When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

MONITOR STRATEGY


Related DTCs
P0031: Air fuel ratio sensor heater (bank 1) open/short (Low electrical current)
P0032: Air fuel ratio sensor heater (bank 1) open/short (High electrical current)
P0051: Air fuel ratio sensor heater (bank 2) open/short (Low electrical current)
P0052: Air fuel ratio sensor heater (bank 2) open/short (High electrical current)
P101D: Air fuel ratio sensor heater (for Bank 1) performance
P103D: Air fuel ratio sensor heater (for Bank 2) performance
Required Sensors/Components (Main)
Air fuel ratio sensor heater
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
10 seconds: P0031 and P0051
10.24 seconds: P0032 and P0052
1 second: P101D and P103D
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P0031 and P0051 
Monitor runs whenever following DTCs not stored
P101D, P103D (Air fuel ratio sensor heater)
One of following conditions met
-
A. All of following conditions met
-
Battery voltage
10.5 V or higher
Time after heater on
5 seconds or more
Active heater OFF control
Not operating
Active heater ON control
Not operating
Air fuel ratio sensor heater duty-cycle
10% or more
B. All of following conditions met
-
Output duty cycle
30% or more

P0032 and P0052 
Monitor runs whenever following DTCs not stored
None
Battery voltage
10.5 V or higher
Time after heater on
5 seconds or more
Active heater OFF control
Not operating
Active heater ON control
Not operating
Air fuel ratio sensor heater duty-cycle
More than 0%

P101D and P103D 
Monitor runs whenever following DTCs not stored
P0031, P0051 (Air fuel ratio sensor heater)
Battery voltage
10.5 V or higher
Time after heater on
5 seconds or more
Active heater OFF control
Not operating
Active heater ON control
Not operating
Air fuel ratio sensor heater duty-cycle
10 to 60%
Air fuel ratio sensor heater ON current
0.8 A or higher

TYPICAL MALFUNCTION THRESHOLDS


P0031 and P0051 
Air fuel ratio sensor heater current
Below 0.8 A

P0032 and P0052 
All of following condition met
-
Air fuel ratio sensor heater output
ON
Hybrid IC high current limiter monitor
Fail

P101D and P103D 
All of following condition met
-
Air fuel ratio sensor heater OFF current
Higher than 11 A
Hybrid IC high current limiter monitor input
Fail

COMPONENT OPERATING RANGE


Air fuel ratio sensor heater current
0.8 A or higher

CONFIRMATION DRIVING PATTERN


A198819E21

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and idle it for 5 minutes or more [B].
  7. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
  8. Idle the engine for 5 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0031, P0032, P0051, P0052, P101D or P103D.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
  14. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.
  15. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  4. Sensor 1 refers to the sensor closest to the engine assembly.
  5. Sensor 2 refers to the sensor farthest away from the engine assembly.
  6. Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the air fuel ratio sensor output voltage . If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
  1. Inspect the air fuel ratio sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


2.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)
A150242E53
  1. Disconnect the air fuel ratio sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D33-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    D34-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *A
    for Bank 1 Sensor 1
    *B
    for Bank 2 Sensor 1
    *a
    Front view of wire harness connector
    (to Air Fuel Ratio Sensor)



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    D33-1 (HA1A) - D74-22 (HA1A)
    Always
    Below 1 Ω
    D34-1 (HA2A) - D74-20 (HA2A)
    Always
    Below 1 Ω
    D33-1 (HA1A) or D74-22 (HA1A) - Body ground
    Always
    10 kΩ or higher
    D34-1 (HA2A) or D74-20 (HA2A) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032, P0051, P0052, P101D OR P103D)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Read the output pending DTCs using the Techstream.

    Result 
    Result
    Proceed to
    No pending DTC is output
    A
    Pending DTC P0031, P0032, P0051, P0052, P101D or P103D is output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.INSPECT NO. 1 INTEGRATION RELAY (A/F)
  1. Inspect the No. 1 integration relay (A/F) .



NG
REPLACE NO. 1 INTEGRATION RELAY
OK


6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (A/F) - A/F SENSOR AND BODY GROUND)
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    D33-2 (+B) - 1A-4
    Always
    Below 1 Ω
    D34-2 (+B) - 1A-4
    Always
    Below 1 Ω
    1A-2 - 1B-5
    Always
    Below 1 Ω
    1A-3 - Body ground
    Always
    Below 1 Ω
    D33-2 (+B) or 1A-4 - Body ground
    Always
    10 kΩ or higher
    D34-2 (+B) or 1A-4 - Body ground
    Always
    10 kΩ or higher
    1A-2 or 1B-5 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)