Home › ENGINE · 3UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P014C    A/F Sensor Slow Response - Rich to Lean Bank 1 Sensor 1

DTC    P014D    A/F Sensor Slow Response - Lean to Rich Bank 1 Sensor 1

DTC    P014E    A/F Sensor Slow Response - Rich to Lean Bank 2 Sensor 1

DTC    P014F    A/F Sensor Slow Response - Lean to Rich Bank 2 Sensor 1

DTC    P015A    A/F Sensor Delayed Response - Rich to Lean Bank 1 Sensor 1

DTC    P015B    A/F Sensor Delayed Response - Lean to Rich Bank 1 Sensor 1

DTC    P015C    A/F Sensor Delayed Response - Rich to Lean Bank 2 Sensor 1

DTC    P015D    A/F Sensor Delayed Response - Lean to Rich Bank 2 Sensor 1

for Preparation Click here


DESCRIPTION

HINT:
Refer to DTC P2195 .


DTC No.
DTC Detection Condition
Trouble Area
P014C
The "Rich to Lean response rate deterioration level*" value is less than the standard.
(2 trip detection logic)
  1. Air fuel ratio sensor (for bank 1 sensor 1)
  2. Air fuel ratio sensor (for bank 1 sensor 1) heater
  3. ECM
P014D
The "Lean to Rich response rate deterioration level*" value is more than the standard.
(2 trip detection logic)
P014E
The "Rich to Lean response rate deterioration level*" value is less than the standard.
(2 trip detection logic)
  1. Air fuel ratio sensor (for bank 2 sensor 1)
  2. Air fuel ratio sensor (for bank 2 sensor 1) heater
  3. ECM
P014F
The "Lean to Rich response rate deterioration level*" value is more than the standard.
(2 trip detection logic)
P015A
The "Rich to Lean delay level*" value is less than the standard.
(2 trip detection logic)
  1. Air fuel ratio sensor (for bank 1 sensor 1)
  2. Air fuel ratio sensor (for bank 1 sensor 1) heater
  3. ECM
P015B
The "Lean to Rich delay level*" value is more than the standard.
(2 trip detection logic)
P015C
The "Rich to Lean delay level*" value is less than the standard.
(2 trip detection logic)
  1. Air fuel ratio sensor (for bank 2 sensor 1)
  2. Air fuel ratio sensor (for bank 2 sensor 1) heater
  3. ECM
P015D
The "Lean to Rich delay level*" value is more than the standard.
(2 trip detection logic)
*: Calculated by the ECM based on the air fuel ratio sensor output

MONITOR DESCRIPTION

After the engine is warm, the ECM carries out air-fuel ratio feedback control, and maintains the air-fuel ratio at the stoichiometric level. In addition, after all the preconditions have been met, active air-fuel ratio control is carried out for approx. 10 seconds, and during active air-fuel ratio control, the ECM measures the response of the air fuel ratio sensor by increasing or decreasing the injection volume by a specific quantity based on the stoichiometric air-fuel ratio learned during normal air-fuel control. The ECM determines whether there is an air fuel ratio sensor malfunction at the mid-point of active air-fuel ratio control.
If the air fuel ratio sensor's response ability is reduced, DTC P014C, P014D, P014E and P014F are stored.
If the time it takes the air fuel ratio sensor output to change is delayed, DTC P015A, P015B, P015C and P015D are stored.

A223538E07


MONITOR STRATEGY


Related DTCs
P014C: Air fuel ratio sensor (bank 1) slow response (rich to lean)
P014D: Air fuel ratio sensor (bank 1) slow response (lean to rich)
P014E: Air fuel ratio sensor (bank 2) slow response (rich to lean)
P014F: Air fuel ratio sensor (bank 2) slow response (lean to rich)
P015A: Air fuel ratio sensor (bank 1) delayed response (rich to lean)
P015B: Air fuel ratio sensor (bank 1) delayed response (lean to rich)
P015C: Air fuel ratio sensor (bank 2) delayed response (rich to lean)
P015D: Air fuel ratio sensor (bank 2) delayed response (lean to rich)
Required Sensors/Components (Main)
Air fuel ratio sensor
Required Sensors/Components (Related)
Vehicle speed sensor, crankshaft position sensor
Frequency of Operation
Once per driving cycle
Duration
10 to 15 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not stored
None
Active air fuel ratio control
Performing
Active air fuel ratio control is performed when the following conditions met
-
Battery voltage
11 V or higher
Engine coolant temperature
75°C (167°F) or higher
Idle
OFF
Engine speed
1000 to 2500 rpm
Air fuel ratio sensor status
Activated
Fuel-cut
OFF
Engine load
10 to 70%
Shift position
2nd or higher
Catalyst monitor
Not executed
Mass air flow
4.0 to 11.4 gm/sec

TYPICAL MALFUNCTION THRESHOLDS


Air Fuel Ratio Sensor Slow Response (Rich to Lean) 
Rich to Lean response rate deterioration level
0.03 V or less

Air Fuel Ratio Sensor Slow Response (Lean to Rich) 
Lean to Rich response rate deterioration level
-0.035 V or higher

Air Fuel Ratio Sensor Delayed Response (Rich to Lean) 
Rich to Lean delay level
350 ms or more

Air Fuel Ratio Sensor Delayed Response (Lean to Rich) 
Lean to Rich delay level
350 ms or more

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN

HINT:
Performing this confirmation driving pattern will activate the air fuel ratio sensor response monitor.


A201252E02

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the Techstream on.
  7. Enter the following menus: Powertrain / Engine and ECT / Monitor / O2 Sensor.
  8. Check that the monitor item O2 Sensor is Incomplete.

    HINT:
    The test values for the test items RL RES RATE B1S1, LR RES RATE B1S1, RL DELAY B1S1, LR DELAY B1S1, RL RES RATE B2S1, LR RES RATE B2S1, RL DELAY B2S1 and LR DELAY B2S1 do not exist in the Detail of O2 Sensor monitor at this time (the initial value of "0.000" is indicated for each test item).

  9. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
  10. Drive the vehicle at a constant speed of between 75 and 100 km/h (47 and 62 mph) for 10 minutes [B].
  11. Check that the monitor item O2 Sensor becomes Complete.

    HINT:
    Check the test values on the Techstream by entering the following menus: Powertrain / Engine and ECT / Monitor / O2 Sensor /Details / RL RES RATE B1S1, LR RES RATE B1S1, RL DELAY B1S1, LR DELAY B1S1, RL RES RATE B2S1, LR RES RATE B2S1, RL DELAY B2S1 and LR DELAY B2S1.

  12. If the monitor item O2 Sensor does not become Complete (if the test values indicated on the Techstream do not change), perform Readiness Monitor Drive Pattern for the air fuel ratio sensor and heated oxygen sensor (Click here).
  13. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  14. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  15. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  16. Input the DTC: P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D.
  17. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    If the judgment result shows ABNORMAL, the system has a malfunction.

  18. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
  1. A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
  2. A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
  3. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
  4. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  5. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  6. Sensor 1 refers to the sensor closest to the engine assembly.
  7. Sensor 2 refers to the sensor farthest away from the engine assembly.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C OR P015D)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D is output
    A
    DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D and other DTCs are output
    B

    HINT:
    If any DTCs other than P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
  1. Inspect the air fuel ratio sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the D33 or D34 A/F sensor connector.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Tester Connection
    Condition
    Specified Condition
    D33-1 (HA1A) - D74-22 (HA1A)
    Always
    Below 1 Ω
    D34-1 (HA2A) - D74-20 (HA2A)
    Always
    Below 1 Ω
    D33-1 (HA1A) or D74-22 (HA1A) - Body ground
    Always
    10 kΩ or higher
    D34-1 (HA2A) or D74-20 (HA2A) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK AIR FUEL RATIO SENSOR
  1. Check that the proper air fuel ratio sensor is installed to the vehicle.

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


5.PERFORM CONFIRMATION DRIVING PATTERN
  1. Drive the vehicle according to Confirmation Driving Pattern.


NEXT


6.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C OR P015D)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D is output
    A
    DTC is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


7.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).


NEXT


8.PERFORM CONFIRMATION DRIVING PATTERN
  1. Drive the vehicle according to Confirmation Driving Pattern.


NEXT


9.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C or P015D is output
    B



B
CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO (Click here)
A

END