Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0504    Brake Switch "A" / "B" Correlation

for Preparation Click here


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If signals which indicate the brake pedal is being depressed and released are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:
The normal signal conditions are as shown in the table below.

Signal (ECM Terminal)
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
  1. [OFF] denotes ground potential.
  2. [ON] denotes battery potential (+B).
  3. On the Techstream, the Data List items Stop Light Switch and ST1 are both ON when the brake pedal is depressed because the characteristics of ST1 indication are the opposite of the characteristics of Stop Light Switch indication.


DTC No.
DTC Detection Condition
Trouble Area
P0504
Conditions (a), (b) and (c) are met for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch is ON.
(b) Brake pedal is released.
(c) STP signal is OFF when the ST1- signal is OFF.
  1. Short in stop light switch signal circuit
  2. STOP fuse
  3. IGN fuse
  4. Stop light switch assembly
  5. ECM

WIRING DIAGRAM


A247752E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses of circuits related to this system before performing the following inspection procedure.

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Stop light switch conditions can be checked using the Techstream.
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Stop Light Switch and ST1.
    5. Check the Data List when the brake pedal is depressed and released.


Brake Pedal Operation
Stop Light Switch
ST1
Depressed
ON
ON
Released
OFF
OFF
1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE)
A148738E28
  1. Disconnect the stop light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A4-2 - Body ground
    Always
    11 to 14 V
    A4-4 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Inspect the stop light switch assembly .



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


3.CHECK ECM (STP AND ST1- VOLTAGE)
A247757E03
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Brake Pedal Operation
    Specified Condition
    A24-35 (ST1-) - Body ground
    Released
    7.5 to 14 V
    Depressed
    0 to 1.5 V
    A24-36 (STP) - Body ground
    Released
    0 to 1.5 V
    Depressed
    7.5 to 14 V

    Text in Illustration 
    *a
    Brake Pedal Depressed
    *b
    Brake Pedal Released
    *c
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)