Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0014    Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1)

DTC    P0015    Camshaft Position "B" - Timing Over-Retarded (Bank 1)

DTC    P0024    Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 2)

DTC    P0025    Camshaft Position "B" - Timing Over-Retarded (Bank 2)

for Preparation Click here


DESCRIPTION

HINT:
If DTC P0014, P0015, P0024 or P0025 is output, check the VVT (Variable Valve Timing) system.

The Variable Valve Timing (VVT) system includes the ECM, camshaft timing oil control valve and VVT controller. The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the camshaft timing oil control valve based on the signals transmitted by several sensors. The VVT controller regulates the exhaust camshaft angle using oil pressure through the camshaft timing oil control valve. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual exhaust valve timing using signals from the VVT and crankshaft position sensors and performs feedback control. This is how the target exhaust valve timing is verified by the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P0014
P0024
Exhaust valve timing is not adjusted in the advance range (2 trip detection logic).
  1. Valve timing
  2. Camshaft timing oil control valve assembly (for exhaust side)
  3. Oil control valve filter
  4. Camshaft timing exhaust gear assembly
  5. ECM
P0015
P0025
Exhaust valve timing is not adjusted in the retard range (1 trip detection logic).
  1. Valve timing
  2. Camshaft timing oil control valve assembly (for exhaust side)
  3. Oil control valve filter
  4. Camshaft timing exhaust gear assembly
  5. ECM

MONITOR DESCRIPTION

  1. The ECM optimizes the exhaust valve timing using the VVT (Variable Valve Timing) system to control the exhaust camshaft. The VVT system includes the ECM, camshaft timing oil control valve and VVT controller.
  2. The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the exhaust camshaft.
    If the difference between the target and actual exhaust valve timing is large, and changes in actual exhaust valve timing are small, the ECM interprets this as the VVT controller being stuck and stores a DTC.
    1. Example:
      A DTC is stored when the following conditions 1 and 2 are met:
    2. 1. It takes 5 seconds or more to change the valve timing by 5°CA.
    3. 2. After the above condition 1 is met, the camshaft timing oil control valve is forcibly activated for 10 seconds.
  3. DTCs P0014 and P0024 (Advanced Cam Timing) are subject to 2 trip detection logic.
  4. DTCs P0015 and P0025 (Retarded Cam Timing) are subject to 1 trip detection logic.
    These DTCs indicate that the VVT controller cannot operate properly due to camshaft timing oil control valve malfunctions or the presence of foreign objects in the camshaft timing oil control valve.

MONITOR STRATEGY


Related DTCs
P0014: Advanced camshaft timing (bank 1)
P0015: Retarded camshaft timing (bank 1)
P0024: Advanced camshaft timing (bank 2)
P0025: Retarded camshaft timing (bank 2)
Required sensors/components (Main)
Camshaft timing oil control valve assembly and camshaft timing exhaust gear assembly
Required sensors/components (Related)
Crankshaft position sensor, VVT sensor and Engine coolant temperature sensor
Frequency of operation
Continuous
Duration
Within 10 seconds
MIL operation
Advanced camshaft timing: 2 driving cycles
Retarded camshaft timing: Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not stored
P0013, P0023 (Exhaust VVT Oil Control Valve)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0102, P0103 (Mass Air Flow Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0335 (Crankshaft Position Sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
Battery voltage
11 V or higher
Engine speed
500 to 4000 rpm
Engine coolant temperature
75 to 100°C (167 to 212°F)

TYPICAL MALFUNCTION THRESHOLDS


Advanced Camshaft Timing 
Both conditions are met:
-
Deviation of actual valve timing and target valve timing
More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit.
Valve timing
No change at advanced valve timing

Retarded Camshaft Timing 
Both conditions are met:
-
Deviation of actual valve timing and target valve timing
More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit.
Valve timing
No change at retarded valve timing

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN


A232050E05

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
  7. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Idle the engine for 3 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0014, P0015, P0024 or P0025.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].

  14. Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Depress the accelerator pedal by a large amount.

  15. Idle the engine for 3 minutes or more [G].
  16. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [H].
  17. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  18. Check the DTC judgment result again.

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the following procedure.

  19. Perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0013 .

INSPECTION PROCEDURE


HINT:

Abnormal Bank
Timing Over-advanced
(Valve Timing is Out of Specified Range)
Timing Over-retarded
(Valve Timing is Out of Specified Range)
Bank 1
P0014
P0015
Bank 2
P0024
P0025
  1. If DTC P0014 or P0015 is output, check the bank 1 VVT system for the exhaust camshaft circuit.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. If DTC P0024 or P0025 is output, check the bank 2 VVT system for the exhaust camshaft circuit.
  4. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  5. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0014, P0015, P0024 OR P0025)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0014, P0015, P0024 or P0025 is output
    A
    P0014, P0015, P0024 or P0025 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0014, P0015, P0024 or P0025 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2).

  1. Check the engine speed while operating the camshaft timing oil control valve using the Techstream.

    OK:

    Techstream Operation
    Specified Condition
    0%
    Normal engine speed
    100%
    Engine idles roughly or stalls



NG
Go to step 4
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025)
  1. Connect the Techstream to the DLC3.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Read the output pending

    OK:
    No pending DTC output.



NG
Go to step 4
OK

END 

4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)


    A103826E11
  1. Remove the cylinder head cover sub-assemblies RH and LH.

  1. Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.

  1. Check that the timing marks on the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.

    1. If not, turn the crankshaft 1 revolution (360°), and then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

    Text in Illustration 
    *1
    Timing Mark

  1. Reinstall the cylinder head cover RH and LH.



NG
ADJUST VALVE TIMING (Click here)
OK


5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE)
  1. Inspect the camshaft timing oil control valve assembly (for exhaust side) (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE) (Click here)
OK


6.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE
A225778E01
  1. Remove the No. 1 or No. 2 oil pipe.

  1. Remove the oil control valve filter.

  1. Check that the filter and pipe are not clogged.

    OK:
    The filter and pipe are not clogged.

    Text in Illustration 
    *1
    No. 1 Oil Pipe
    *2
    No. 2 Oil Pipe

  1. Reinstall the oil control valve filter.

  1. Reinstall the No. 1 or No. 2 oil pipe.



NG
CLEAN OIL CONTROL VALVE FILTER AND OIL PIPE
OK


7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
  1. Replace the camshaft timing exhaust gear assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly (Click here).


NEXT


8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025)
  1. Connect the Techstream to the DLC3.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the output pending.

    OK:
    No pending DTC output.

    HINT:
    DTC P0014, P0015, P0024 or P0025 is stored when foreign objects in the engine oil are caught in some parts of the system. These codes will remain stored even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.



NG
REPLACE ECM (Click here)
OK

SYSTEM IS OK