DTC C2165/65 Abnormal Temperature Inside ID1 Tire |
DTC C2166/66 Abnormal Temperature Inside ID2 Tire |
DTC C2167/67 Abnormal Temperature Inside ID3 Tire |
DTC C2168/68 Abnormal Temperature Inside ID4 Tire |
| DTC Code | DTC Detection Condition | Trouble Area |
| C2165/65 C2166/66 C2167/67 C2168/68 | Temperature inside the tire exceeds 119°C (246.2°F) more than a specified times. |
|
| 1.CHECK TIRES |
Check that the tires are not flat, and have no indication of tire pressure drop.
|
| ||||
| OK | |
| 2.IDENTIFY TRANSMITTER CORRESPONDING TO DTC |
Set the tire pressures to the specified value(s) (Click here).
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and the Techstream on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Display the "ID Tire Inflation Pressure" data for each wheel using the tester.
Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds. If "ID Tire Inflation Pressure" data displayed on the tester (ID1 to ID4) does not change, the tire pressure warning valve and transmitter corresponding to the unchanged "ID Tire Inflation Pressure" data is the cause of the output DTC.
Check the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ID 1 Tire Inflation Pressure | ID1 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| ID 2 Tire Inflation Pressure | ID2 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| ID 3 Tire Inflation Pressure | ID3 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| ID 4 Tire Inflation Pressure | ID4 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| Condition | Detection Condition |
| "Tire Inflation Pressure" data (ID1 to ID4) changed. | Normal |
| One of "Tire Inflation Pressure" data did not change. | Transmitter corresponding to DTC |
When the "ID Tire Inflation Pressure" data (ID1 to ID4) has changed, repeat this procedure to identify the tire pressure warning valve and transmitter that corresponds to the DTC.
When all of the "ID Tire Inflation Pressure" data (ID1 to ID4) has changed, identify the malfunctioning tire pressure warning valve and transmitter using recorded transmitter IDs and the output DTC.
Set the tire pressures to the appropriate specified value(s) (Click here).
| NEXT | |
| 3.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER |
Replace the identified tire pressure warning valve and transmitter with a new one (Click here).
| NEXT | |
| 4.REGISTRATION OF TRANSMITTER ID |
Register the transmitter ID for all 4 tires (Click here).
| NEXT | |
| 5.PERFORM INITIALIZATION |
Perform initialization (Click here).
| NEXT | |
| 6.CONFIRM TIRE INFLATION PRESSURE (DATA LIST) |
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and the Techstream on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ID 1 Tire Inflation Pressure | ID1 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| ID 2 Tire Inflation Pressure | ID2 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| ID 3 Tire Inflation Pressure | ID3 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| ID 4 Tire Inflation Pressure | ID4 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| Result | Proceed to |
| Tire pressure values are not displayed. | A |
| All tire pressure readings are equal to specified values. | B |
|
| ||||
| A | ||
| ||