Home › STEERING › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

DTC    B2611    Telescopic Position Sensor or Telescopic Motor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The telescopic motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and slides the steering column forward and backward. The telescopic position sensor (Hall IC) in the telescopic motor detects the sliding position in the forward and backward directions of the steering column and outputs a signal to the multiplex tilt and telescopic ECU based on that sliding amount.

C152160E04


HINT:
Limit positions can be confirmed on the screen of the intelligent tester or Techstream.

DTC Code
Detection Condition
Trouble Area
B2611
Telescopic operation stops within the operation range while operating.
  1. Harness or connector
  2. Telescopic position sensor or telescopic motor
  3. Multiplex tilt and telescopic ECU


WIRING DIAGRAM


C162229E01


INSPECTION PROCEDURE

HINT:
The wire harness between the multiplex tilt and telescopic ECU and telescopic motor is provided with the steering column assembly.

1.PERFORM ACTIVE TEST USING TECHSTREAM (TELESCO SHORT/LONG)
C106469E01
  1. Select the Active Test, use the Techstream to generate a control command, and then check that the steering column contracts and extends.

    Tilt & Telescopic 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Telesco operation
    Telescopic operation
    Long / Short
    -
    Result 
    Result
    Proceed to
    The steering column does not contract (extend).
    A
    The steering column contracts (extends).
    B



B
Go to step 3
A


2.CHECK TELESCOPIC MOTOR


    C149086E03
  1. Disconnect connector A from the multiplex tilt and telescopic ECU.

  1. Apply 12 V battery voltage to the multiplex tilt and telescopic ECU connector. Then check the steering wheel telescopic operation.

    OK 
    Measurement Condition
    Specified Condition
    12 V battery positive (+) lead → Terminal A-2 (TEM+)
    12 V battery negative (-) lead → Terminal A-6 (TEM-)
    The steering column contracts.
    12 V battery positive (+) lead → Terminal A-6 (TEM-)
    12 V battery negative (-) lead → Terminal A-2 (TEM+)
    The steering column extends



NG
REPLACE STEERING COLUMN ASSEMBLY (Click here)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)  

3.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCE TERMINAL VOLTAGE)


    C149088E14
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A-3 (VCE) - A-5 (E2)
    Ignition switch ON
    8 to 16 V



NG
Go to step 5
OK


4.CHECK TELESCOPIC POSITION SENSOR


    C149088E15
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A-4 (TES) - A-5 (E2)
    Telescopic steering contracted or extended
    Pulse generation
    High: 8 to 16 V
    Low: Below 1 V



NG
REPLACE STEERING COLUMN ASSEMBLY (Click here)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)  

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TELESCOPIC POSITION SENSOR)


    C149086E04
  1. Disconnect connector A from the multiplex tilt and telescopic ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-3 (VCE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)


    C149087E15
  1. Disconnect the J47 multiplex tilt and telescopic ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J47-11 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)