DTC B1810/53 Short in Driver Side Squib 2nd Step Circuit |
DTC B1811/53 Open in Driver Side Squib 2nd Step Circuit |
DTC B1812/53 Short to GND in Driver Side Squib 2nd Step Circuit |
DTC B1813/53 Short to B+ in Driver Side Squib 2nd Step Circuit |
| DTC Code | Detection Condition | Trouble Area |
| B1810/53 | When one of the following conditions is met:
|
|
| B1811/53 | When one of the following conditions is met:
|
|
| B1812/53 | When one of the following conditions is met:
|
|
| B1813/53 | When one of the following conditions is met:
|
|

| 1.CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the z5 connector from the steering pad.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect SST from connector E.
Check that the spiral cable connectors (on the steering pad side) are not damaged.
|
| ||||
| OK | |
| 3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT |
![]() |
Disconnect the connectors from the center airbag sensor.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z5-1 (D2-) - Body ground | Ignition switch ON | Below 1 V |
| z5-2 (D2+) - Body ground |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z5-1 (D2-) - z5-2 (D2+) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z5-1 (D2-) - z5-2 (D2+) | Always | 1 MΩ or higher |
| z5-1 (D2-) - Body ground | ||
| z5-2 (D2+) - Body ground |
|
| ||||
| OK | |
| 4.CHECK CENTER AIRBAG SENSOR |
![]() |
Connect the connectors to the steering pad and the center airbag sensor.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1810, B1811, B1812 or B1813 is output (for Column Shift Type) | A |
| DTC B1810, B1811, B1812 or B1813 is output (for Floor Shift Type) | B |
| DTC B1810, B1811, B1812 or B1813 is not output | C |
|
| ||||
|
| ||||
| C | ||
| ||
| 5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE) |
![]() |
Restore the released activation prevention mechanism of connector B to the original condition.
Disconnect the instrument panel wire connector from the spiral cable.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J11-3 - Body ground | Ignition switch ON | Below 1 V |
| J11-4 - Body ground |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J11-3 - J11-4 | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J11-3 - J11-4 | Always | 1 MΩ or higher |
| J11-3 - Body ground | ||
| J11-4 - Body ground |
|
| ||||
| OK | ||
| ||