DTC B1653/35 Seat Position Airbag Sensor Circuit Malfunction |
| DTC Code | Detection Condition | Trouble Area |
| B1653/35 | When one of the following conditions is met:
|
|

| 1.CHECK FOR DTC |
![]() |
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the seat position airbag sensor.
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor and the seat position airbag sensor.
Check that the connectors (on the center airbag sensor side and seat position airbag sensor side) are not damaged.
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - SEAT POSITION AIRBAG SENSOR) |

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| P7-3 (LSP+) - Body ground | Ignition switch ON | Below 1 V |
| P7-4 (LSP-) - Body ground |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect terminals 13 (DSP-) and 14 (DSP+) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P7-3 (LSP+) - P7-4 (LSP-) | Always | Below 1 Ω |
Disconnect the service wire from the connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P7-3 (LSP+) - P7-4 (LSP-) | Always | 1 MΩ or higher |
| P7-3 (LSP+) - Body ground | ||
| P7-4 (LSP-) - Body ground |
|
| ||||
| OK | |
| 5.CHECK SEAT POSITION AIRBAG SENSOR (FRONT SEAT INNER BELT LH) |
![]() |
Connect the connectors to the center airbag sensor and the seat position airbag sensor.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 6.REPLACE SEAT POSITION AIRBAG SENSOR (FRONT SEAT INNER BELT LH) |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the front seat inner belt LH (Click here).
| NEXT | |
| 7.CHECK CENTER AIRBAG SENSOR |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1653 is output (for Column Shift Type) | A |
| DTC B1653 is output (for Floor Shift Type) | B |
| DTC B1653 is not output | C |
|
| ||||
|
| ||||
| C | ||
| ||