DTC P0451 Evaporative Emission Control System Pressure Sensor Range / Performance |
DTC P0452 Evaporative Emission Control System Pressure Sensor / Switch Low Input |
DTC P0453 Evaporative Emission Control System Pressure Sensor / Switch High Input |
| DTC No. | Monitoring Item | Malfunction Detection Condition | Trouble Area | Detection Timing | Detection Logic |
| P0451 | Canister pressure sensor signal noise | Sensor output voltage fluctuates frequently within a certain time period. |
|
| 2 trip |
| P0451 | Canister pressure sensor becomes fixed/flat | Sensor output voltage does not vary within certain time period. |
|
| 2 trip |
| P0452 | Canister pressure sensor low input | EVAP pressure is below 42.1 kPa-a (315.9 mmHg-a) for 0.5 seconds. |
|
| 1 trip |
| P0453 | Canister pressure sensor high input | EVAP pressure is higher than 123.8 kPa-a (928.4 mmHg-a) for 0.5 seconds. |
|
| 1 trip |

| Required Sensors/Components | Canister pump module |
| Frequency of Operation | Once per driving cycle: P0451 sensor fixed/flat Continuous: P0451 sensor noise, P0452 and P0453 |
| Duration | Within 15 seconds: P0451 sensor noise Within 2 minutes: P0451 sensor fixed/flat 0.5 seconds: P0452 and P0453 |
| MIL Operation | Immediate: P0452 and P0453 2 driving cycles: P0451 |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | P0452, P0453 (EVAP System) |
| Atmospheric pressure (absolute pressure) | 70 to 110 kPa-a (525 to 825 mmHg-a) |
| Battery voltage | 10.5 V or higher |
| Intake air temperature | 4.4 to 35°C (40 to 95°F) |
| Either of following conditions met | A or B |
| A. Engine condition | Running |
| B. Time after key-off | 5, 7 or 9.5 hours |
| Monitor runs whenever following DTCs not stored | P0452, P0453 (EVAP System) |
| Battery voltage | 10.5 V or more |
| Intake air temperature | 4.4 to 35°C (40 to 95°F) |
| Atmospheric pressure (absolute pressure) | 70 to 110 kPa-a (525 to 825 mmHg-a) |
| Time after key-off | 5, 7 or 9.5 hours |
| Monitor runs whenever following DTCs not stored | None |
| Battery voltage | 8 V or more |
| Starter | OFF |
| Either of following conditions met | (a) or (b) |
| (a) Ignition switch | ON |
| (b) Soak timer | ON |
| Frequency that EVAP pressure changes 0.3 kPa-g (2.25 mmHg-g) or more | 10 times or more in 10 seconds |
| EVAP pressure change during reference pressure measurement | Less than 0.65 kPa-a (4.87 mmHg-a) |
| EVAP pressure | Below 42.1 kPa-a (315.9 mmHg-a) |
| EVAP pressure | Higher than 123.8 kPa-a (928.4 mmHg-a) |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CONFIRM DTC AND EVAP PRESSURE |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (do not start the engine).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Code.
Read the DTCs.
Enter the following menus: Powertrain / Engine and ECT / Data List / Vapor Pressure Pump.
Read the EVAP (Evaporative Emission) pressure displayed on the Techstream.
| Display (DTC Output) | Test Result | Suspected Trouble Area | Proceed to |
| P0451 | - | Canister pressure sensor | C |
| P0452 | Below 42.1 kPa-a (315.9 mmHg-a) |
| A |
| P0453 | Higher than 123.8 kPa-a (928.4 mmHg-a) |
| B |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
Turn the ignition switch off.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Test Result | Suspected Trouble Area | Proceed to |
| D74-121 (PPMP) - Body ground | Always | 10 Ω or less |
| A |
| 10 kΩ or higher |
| B |
Reconnect the ECM connector.
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
Disconnect the canister pump module connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Test Result | Suspected Trouble Area | Proceed to |
| D74-121 (PPMP) - Body ground | Always | 10 kΩ or higher | Short in canister pressure sensor circuit | A |
| 10 Ω or less | Short in wire harness/connector (ECM - Canister pressure sensor) | B |
Reconnect the canister pump module connector.
Reconnect the ECM connector.
|
| ||||
|
| ||||
| 4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |

Disconnect the canister pump module connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R12-8 (SGND) - Body ground | Always | 100 Ω or less |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| R12-6 (VCC) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| R12-7 (VOUT) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| Test Result | Suspected Trouble Area | Proceed to |
| Voltage and resistance within standard ranges | Open in canister pressure sensor circuit | A |
| Voltage and resistance outside standard ranges | Open in wire harness/connector (ECM - Canister pressure sensor) | B |
| *a | Front view of wire harness connector (to Canister Pump Module) |
|
| ||||
| A | |
| 5.REPLACE CANISTER PUMP MODULE |
Replace the canister pump module (Click here).

| *1 | Fuel Tank | *2 | Fuel Tank Vent Hose |
| *3 | Canister Assembly | *4 | Canister Pump Module - Canister Pressure Sensor - Leak Detection Pump - Vent Valve |
| *5 | Fuel Tank Inlet Pipe Sub-Assembly (Canister Filter) | *6 | Canister Outlet Hose |
| *a | Inspection Area (check for disconnection and/or cracks) | - | - |
|
| ||||
| 6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM) |
|
| ||||
| 7.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Perform the Evaporative System Check using the Techstream, referring to the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0451, P0452 or P0453.
Check the DTC judgment result.
| NEXT | ||
| ||