Home › ENGINE · 3UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2431    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1

DTC    P2432    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank1

DTC    P2433    Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank1

DTC    P2436    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank 2

DTC    P2437    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank 2

DTC    P2438    Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank 2

for Preparation Click here


DESCRIPTION

The Secondary Air injection (AIR) system consists of an air pump, the Air Switching Valve (ASV), a pressure sensor, the Air Injection Control Driver (AID) and the ECM. For a short time after cold engine starts, the AIR system pumps secondary air to the exhaust port of the cylinder head to purify the exhaust emissions. The secondary air is supplied by the air pump and is pumped to the exhaust port through the ASV.
The AID drives the ASV and the air pump according to command signals transmitted by the ECM. The pressure sensor detects the pressure in the secondary air passage when the AIR system is ON and OFF, and transmits a pressure signal to the ECM.
The AID is not only equipped to drive the pump and valve, but also with a diagnosis function to detect malfunctions in the AIR system circuit.

HINT:
As a large current is required to drive the air pump and ASV, an AID is installed to this system.


A162565E01


DTC Code
DTC Detection Condition
Trouble Area
P2431
P2436
Pressure sensor indicates less than 45.6 kPa (342 mmHg), or more than 135 kPa (1013 mmHg) (2 trip detection logic)
  1. Pressure sensor
  2. Open or short in pressure sensor circuit
  3. ECM
P2432
P2437
While engine running, voltage output of pressure sensor remains below 0.5 V (1 trip detection logic)
  1. Pressure sensor
  2. Open or short in pressure sensor circuit
  3. ECM
P2433
P2438
While engine running, voltage output of pressure sensor remains above 4.5 V (1 trip detection logic)
  1. Pressure sensor
  2. Open or short in pressure sensor circuit
  3. ECM

MONITOR DESCRIPTION

A085160E08
The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the air switching valve in the secondary air injection system.
If there is a defect in the sensor or the sensor circuit, the voltage level deviates from the normal operating range, the ECM interprets this deviation as a malfunction in the pressure sensor or circuit and sets a DTC.

MONITOR STRATEGY


Related DTCs
P2431: Air flow/Pressure sensor circuit rationality
P2432: Air flow/Pressure sensor circuit range check (Low voltage)
P2433: Air flow/Pressure sensor circuit range check (High voltage)
P2436: Air flow/Pressure sensor circuit rationality
P2437: Air flow/Pressure sensor circuit range check (Low voltage)
P2438: Air flow/Pressure sensor circuit range check (High voltage)
Required Sensors/Components (Main)
Pressure sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
P2432, P2433, P2437, P2438: 0.5 seconds
P2431, P2436: 5 seconds
MIL Operation
P2432, P2433, P2437, P2438: Immediate
P2431, P2436: 2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P2431 and P2436: 
Monitor runs whenever following DTCs not present
P2432, P2433, P2437, P2438 (AIR Pressure Sensor - Low/High)
All of following conditions met:
-
Starter
OFF
Battery voltage
8 V or more
Ignition switch
ON

P2432, P2433, P2437 and P2438 
Monitor runs whenever following DTCs not present
None
All of following conditions met:
-
Starter
OFF
Battery voltage
8 V or more
Ignition switch
ON

TYPICAL MALFUNCTION THRESHOLDS


P2431 and P2436: 
Air pressure
Less than 45.6 kPa (342 mmHg), or more than 135 kPa (1013 mmHg)

P2432 and P2437: 
Air pressure sensor voltage
Less than 0.5 V

P2433 and P2438: 
Air pressure sensor voltage
More than 4.5 V

COMPONENT OPERATING RANGE


Air pressure sensor voltage
Between 0.5 V and 4.5 V

CONFIRMATION DRIVING PATTERN


A199319E04

NOTICE:
  1. This Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.
    Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
    While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
    If an ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
  2. Performing the Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
  3. When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
  4. Turn the ignition switch off when the Air Injection Check operation finishes.

  1. Start the engine and warm it up.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Clear DTCs (if set) (Click here).
  7. Turn the ignition switch off and wait for at least 30 seconds.
  8. Turn the ignition switch to ON and turn the Techstream on [A].
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / Air injection check / Automatic Mode.
  10. Start the engine after the Techstream initialization is finished.
  11. Perform the System Check operation by pressing ENTER (Next).
  12. After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the ENTER (Exit).
  13. Check pending DTCs [B].

    OK:
    No pending DTC is output.

  14. After the "Air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P2431, P2432, P2433, P2436, P2437 or P2438.
  16. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  17. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If no permanent DTC is output, the system is normal.
    2. If a permanent DTC is output, the system is malfunctioning.

  18. Turn the ignition switch off.

WIRING DIAGRAM

Refer to DTC P0412 .

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.

1.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - ECM)
  1. Disconnect the D58 or D59 air switching valve connector.

  1. Disconnect the A24 and D74 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Tester Connection
    Condition
    Specified Condition
    D58-3 (AIP) - A24-54 (AIP)
    Always
    Below 1 Ω
    D58-2 (VC) - D74-67 (VCV1)
    Always
    Below 1 Ω
    D58-4 (E2) - D74-98 (ETHA)
    Always
    Below 1 Ω
    D59-3 (AIP2) - A24-53 (AIP2)
    Always
    Below 1 Ω
    D59-2 (VC2) - D74-67 (VCV1)
    Always
    Below 1 Ω
    D59-4 (E22) - D74-97 (ETHW)
    Always
    Below 1 Ω
    D58-3 (AIP) or A24-54 (AIP) - Body ground
    Always
    10 kΩ or higher
    D58-2 (VC) or D74-67 (VCV1) - Body ground
    Always
    10 kΩ or higher
    D59-3 (AIP2) or A24-53 (AIP2) - Body ground
    Always
    10 kΩ or higher
    D59-2 (VC2) or D74-67 (VCV1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT AIR SWITCHING VALVE (PRESSURE SENSOR)
A165753E01
  1. Connect a pressure gauge to the air pressure sensor as shown in the illustration.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (absolute) and Air Pump2 Pressure (Absolute).

  1. Check that the pressure displayed on the Techstream fluctuates when applying the pressure to the pressure sensor with the pressure gauge.

    NOTICE:
    Do not let foreign matter enter the sensor when applying pressure.

    OK:
    Pressure fluctuates in response to pressure applied with pressure gauge.

    HINT:
    The Techstream displays the air pump pressure as absolute pressure.



NG
REPLACE AIR SWITCHING VALVE ASSEMBLY (Click here)
OK

REPLACE ECM (Click here)