Home › ENGINE ยท 3UR-FE › EMISSION CONTROL › AIR SWITCHING VALVE

AIR SWITCHING VALVE > REMOVAL

for Preparation Click here



1. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY
(Click here)


2. REMOVE INTAKE MANIFOLD
(Click here)


3. REMOVE NO. 9 WATER BY-PASS HOSE


    A307663E01
  1. Slide the 2 clamps and remove the No. 9 water by-pass hose from the separator case and front water by-pass joint.
    Text in Illustration 
    *1
    No. 9 Water By-pass Hose
    *2
    No. 10 Water By-pass Hose



4. REMOVE NO. 10 WATER BY-PASS HOSE
  1. Slide the 2 clamps and remove the No. 10 water by-pass hose from the separator case and front water by-pass joint.



5. REMOVE NO. 1 WATER BY-PASS HOSE


    A307665E02
  1. Slide the 2 clamps and remove the No. 1 water by-pass hose from the front water by-pass joint and water inlet housing.
    Text in Illustration 
    *1
    No. 1 Water By-pass Hose
    *2
    No. 2 Water By-pass Hose



6. DISCONNECT NO. 2 WATER BY-PASS HOSE
  1. Slide the clamp and disconnect the No. 2 water by-pass hose from the front water by-pass joint.



7. DISCONNECT NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY


    A158578
  1. Remove the 3 bolts and disconnect the No. 2 water by-pass pipe sub-assembly.



8. REMOVE NO. 2 ENGINE COVER


A307666


9. DISCONNECT FUEL TUBE CLAMP


    A158580
  1. Disconnect the fuel tube clamp from the bracket.



10. REMOVE NO. 1 ENGINE COVER


A158581


11. REMOVE FRONT WATER BY-PASS JOINT
  1. Disconnect the engine coolant temperature sensor connector.



    A307708
  1. Remove the 4 nuts, front water by-pass joint and 2 gaskets.



12. REMOVE NO. 3 WATER BY-PASS PIPE


A307664

HINT:
Perform this procedure only when replacement of the No. 3 water by-pass pipe is necessary.

  1. Remove the bolt and No. 3 water by-pass pipe.



13. REMOVE AIR TUBE


    A158575E06
  1. Slide the 2 clamps and disconnect the No. 2 air hose and No. 3 air hose.
    Text in Illustration 
    *1
    No. 2 Air Hose
    *2
    No. 3 Air Hose

  1. Disconnect the air pump connector.

  1. Disconnect the air pump connector clamp holder.

  1. Using a clip remover, detach the wire harness claw.



    A158582
  1. Remove the 2 bolts and air tube.

  1. Disconnect the 2 No. 1 air hoses from the air tube.



14. REMOVE AIR SWITCHING VALVE ASSEMBLY


    A158583
  1. Disconnect the knock sensor connector.

  1. Remove the bolt and bracket.

  1. Disconnect the 2 air switching valve assembly connectors.



    A158586
  1. Remove the 3 bolts and air switching valve assembly.



15. REMOVE NO. 2 AIR TUBE


    A158584
  1. Remove the 2 bolts, No. 2 air tube and gasket.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.



16. REMOVE NO. 3 AIR TUBE


    A158585
  1. Remove the 2 bolts, No. 3 air tube and gasket.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.