DTC P2444 Secondary Air Injection System Pump Stuck On Bank1 |
DTC P2445 Secondary Air Injection System Pump Stuck Off Bank1 |
DTC P2446 Secondary Air Injection System Pump Stuck On Bank 2 |
DTC P2447 Secondary Air Injection System Pump Stuck Off Bank 2 |
| DTC Code | DTC Detection Condition | Trouble Area |
| P2444 P2446 | Secondary air pressure more than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn off (2 trip detection logic) |
|
| P2445 P2447 | Secondary air pressure less than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn on (2 trip detection logic) |
|
| When secondary air injection is on, the amount of air from the air pump is below the threshold (2 trip detection logic). |
| Related DTCs | P2444: Air pump stuck ON P2445: Air pump stuck OFF P2446: Air pump stuck ON P2447: Air pump stuck OFF |
| Required Sensors/Components (Main) | Pressure sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Once per drive cycle |
| Duration | 7 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0010, P0020 (VVT Oil control valve) P0011, P0021 (VVT System - Advance) P0012, P0022 (VVT System - Retard) P0013, P0023 (Exhaust VVT Oil Control Valve) P0014, P0024 (Exhaust VVT System - Advance) P0015, P0025 (Exhaust VVT System - Retard) P0016, P0018 (VVT System - Misalignment) P0017, P0019 (Exhaust VVT System - Misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio Sensor Heater) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0171, P0172, P0174, P0175 (Fuel system) P0301 - P0308 (Misfire) P0327, P0328, P0332, P0333, P032C, P032D, P033C, P033D (Knock sensor) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351 - P0358 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0451, P0452, P0453 (EVAP system) P0500, P0722 (Vehicle Speed Sensor) P106B (Evap. emission control system Pressure Sensor - Air Injection System Pressure Sensor correlation) P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor) P1340 Camshaft position sensor P2431 - P2438 (Secondary air injection system pressure sensor) P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance) |
| Battery voltage | 11 V or higher |
| Atmospheric pressure | 45 kPa (337.5 mmHg) or more |
| Engine | Running |
| AIR monitor during AIR: ON*1 | Completed |
| AIR monitor during AIR: OFF*2 | Completed |
| Air injection Driver (open/short or out of range) | Not detected |
| AIR pressure sensor (open/short or out of range) | Not detected |
| Time after AIR in operation | 5 seconds or more |
| AIR pump | ON |
| AIR valve | Open |
| Engine speed | Less than 3550 rpm |
| Intake air amount | Less than 99 gm/sec |
| Time after engine start | 1 second or more |
| Time after AIR in operation | 10 seconds or more |
| AIR pump | OFF |
| AIR valve | Closed |
| Engine speed | Less than 2800 rpm |
| AIR monitor during AIR: ON | Completed |
| Time after engine started | 1 seconds or more |
| Battery voltage | 11 V or higher |
| Atmospheric pressure | 45 kPa (337.5 mmHg) or more |
| Engine | Running |
| Air flow pattern check condition during AIR monitor during AIR: ON* | Completed |
| AIR injection driver fail (open/short or out of range) | Not detected |
| AIR pressure sensor fail (open/short or out of range) | Not detected |
| *: Air flow pattern check condition during AIR monitor during AIR: ON | - |
| AIR valve | Open |
| Time after secondary air injection in operation | 1 second or more |
| Following conditions are met during AIR ON | - |
| Cumulative pressure pulsation | 10 kPa or higher |
| AIR pressure | 2.4 kPa or higher |
| Following conditions are met during AIR ON | - |
| Cumulative pressure pulsation | 10 kPa or higher |
| AIR pressure | Below 2.4 kPa |
| Following conditions are met during AIR ON | - |
| Cumulative pressure pulsation | Below 10 kPa |
| AIR pressure | 2.4 kPa or higher |
| Following conditions are met during AIR ON | - |
| Cumulative pressure pulsation | Below 10 kPa |
| AIR pressure | Below 2.4 kPa |
| Following conditions are met during AIR OFF | - |
| Cumulative pressure pulsation | 30 kPa or higher |
| AIR pressure | 2.4 kPa or higher |
| Following conditions are met during AIR OFF | - |
| Cumulative pressure pulsation | 30 kPa or higher |
| AIR pressure | Below 2.4 kPa |
| Following conditions are met during AIR OFF | - |
| Cumulative pressure pulsation | Below 30 kPa |
| AIR pressure | 2.4 kPa or higher |
| Following conditions are met during AIR OFF | - |
| Cumulative pressure pulsation | Below 30 kPa |
| AIR pressure | Below 2.4 kPa |
| Either condition is met: | (a) or (b) |
| (a) AIR OFF Condition 1 | Met |
| (b) AIR OFF Condition 3 | Met |
| Either condition is met: | (a) or (b) |
| (a) AIR ON Condition 2 | Met |
| (b) AIR ON Condition 4 | Met |
| Cumulative pressure pulsation | (a) or (b) |
| (a) Air flow value at Bank 1 or Bank 2 | 140 L/min or less |
| (b) Air flow value at Bank 1 and Bank 2 | 140 L/min or less |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Air Pump | ON |
| Air Switching Valve | Open |
| Pressure | 2.4 kPa or more |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | OFF |
| Air Switching Valve | Open |
| Pressure | Less than 2.4 kPa |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | ON |
| Air Switching Valve | Closed |
| Pressure | 2.4 kPa or more |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | OFF |
| Air Switching Valve | Close |
| Pressure | Less than 2.4 kPa |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | ON |
| Air Switching Valve | Open |
| Pressure | 2.4 kPa or more |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | OFF |
| Air Switching Valve | Open |
| Pressure | Less than 2.4 kPa |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | ON |
| Air Switching Valve | Closed |
| Pressure | 2.4 kPa or more |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | OFF |
| Air Switching Valve | Close |
| Pressure | Less than 2.4 kPa |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Detected Conditions while AIR operating: Air pump ON, ASV Open | Detected Conditions while AIR not operating: Air pump OFF, ASV Closed | ECM Determination | DTCs Output |
| Case 1 | Case 8 | Normal | - |
| Case 1 | Case 6 | ASV stuck open | P2440 or P2442 |
| Case 1 | Case 7 | Air pump stuck ON | P2444 or P2446 |
| Case 2 | Case 8 | Air pump stuck OFF | P2445 or P2447 |
| Case 3 | Case 8 | ASV stuck closed | P2441 or P2443 |
| Case 1 | Case 5 | ASV stuck open and air pump stuck ON | P2440 and P2444 or P2442 and P2446 |
| Case 2 | Case 6 | ASV stuck open and air pump stuck OFF | P2440 and P2445 or P2442 and P2447 |
| Case 3 | Case 7 | ASV stuck closed and air pump stuck ON | P2441 and P2444 or P2443 and P2446 |
| Case 4 | Case 8 | ASV stuck closed and air pump stuck OFF | P2441 and P2445 or P2443 and P2447 |
| Operation | AIR PUMP | ASV | PRESSURE*1 | PULSATION*2 |
| AIR PUMP: ON, ASV: OPEN | ON | OPEN | 2.4 kPa or more | 20 kPa or more |
| AIR PUMP: OFF, ASV: CLOSE | OFF | CLOSE | Less than 2.4 kPa | Less than 30 kPa |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2444, P2445, P2446 AND/OR P2447) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P2444, P2445, P2446 and/or P2447 are output | A |
| P2444, P2445, P2446 and/or P2447 and other DTCs (except P0418 and P0419) are output | B |
| P2444, P2445, P2446 and/or P2447 and P0418 and/or P0419 are output | C |
|
| ||||
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE AIR PUMP HEATER) |
![]() |
Disconnect the air pump connector.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT/ Active Test / Activate the Air Pump Heater.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D89-1 - Body ground | Activate the Air Pump Heater is ON | 11 to 14 V |
| D90-1 - Body ground | Activate the Air Pump Heater is ON | 11 to 14 V |
Reconnect the air pump connector.
|
| ||||
| OK | |
| 3.INSPECT AIR PUMP ASSEMBLY (BANK 1 OR BANK 2) (HEATER RESISTANCE) |
Inspect the air pump assembly (bank 1 or bank 2) (Click here).
|
| ||||
| OK | |
| 4.INSPECT AIR PUMP HEATER RELAY |
Inspect the air pump heater relay (Click here).
|
| ||||
| OK | |
| 5.CHECK AIR PUMP HEATER RELAY (POWER SOURCE) |
Remove the air pump heater relay (AI-HTR).
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Air pump heater relay terminal 5 - Body ground | Always | 11 to 14 V |
Reinstall the air pump heater relay (AI-HTR).
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (AIR PUMP - AIR PUMP HEATER RELAY, BODY GROUND) |
Remove the air pump heater relay (AI-HTR).
Disconnect the air pump connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| AI-HTR relay terminal 3 - D89-1 (APH+) | Always | Below 1 Ω |
| AI-HTR relay terminal 3 - D90-1 (APH+) | Always | Below 1 Ω |
| D89-3 (APHG) - Body ground | Always | Below 1 Ω |
| D90-3 (APHG) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| AI-HTR relay terminal 3 or D89-1 (APH+) - Body ground | Always | 10 kΩ or higher |
| AI-HTR relay terminal 3 or D90-1 (APH+) - Body ground | Always | 10 kΩ or higher |
Reinstall the air pump heater relay (AI-HTR).
Reconnect the air pump connector.
|
| ||||
| OK | |
| 7.PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.
Start the engine.
Perform the AIR system intrusive operation while the engine is idling.
Check that the air pump (AIR PUMP), ASV and pressure in the AIR system passage (PRESSURE) status displayed on the Techstream indicate the conditions shown in the table below.
| Operation | AIR PUMP | ASV | PRESSURE* |
| AIR PUMP: ON, ASV: OPEN | ON | OPEN | 2.4 kPa or more |
| AIR PUMP: OFF, ASV: CLOSE | OFF | CLOSE | Less than 2.4 kPa |
Turn the ignition switch off.
|
| ||||
| OK | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2247) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (if set) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Automatic Mode.
Start the engine after the Techstream initialization is finished.
Perform the System Check operation by pressing Next.
After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.
Check pending DTCs.
Turn the ignition switch off.
| Result | Proceed to |
| P2444, P2445, P2446 and/or P2447 are output | A |
| No pending DTC is output | B |
|
| ||||
| A | |
| 9.CHECK VACUUM HOSES (PRESSURE SENSOR - AIR SWITCHING VALVE) |
Check the vacuum hose connections with the pressure sensor and ASV.
Inspect the vacuum hose for blockages and damage.
|
| ||||
| OK | |
| 10.INSPECT AIR SWITCHING VALVE ASSEMBLY (PRESSURE SENSOR) |
![]() |
Connect a pressure gauge to the air pressure sensor as shown in the illustration.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (absolute) and Air Pump2 Pressure (Absolute).
Check that the pressure displayed on the Techstream fluctuates when applying the pressure to the pressure sensor with the pressure gauge.
|
| ||||
| OK | |
| 11.CHECK AIR INJECTION SYSTEM PIPE CONNECTIONS |

Check that all the pipes and hoses between the air pump and ASV are securely connected.
Inspect the pipes and hoses for blockages and damage.
|
| ||||
| OK | |
| 12.INSPECT AIR INJECTION CONTROL DRIVER (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT) |
![]() |
Disconnect the D48 and D50 or D52 and D54 AID connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D50-1 (E) - Body ground | Always | Below 1 Ω |
| D54-1 (E2) - Body ground | Always | Below 1 Ω |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D48-1 (BATT) - Body ground | Always | 11 to 14 V (near battery voltage) |
| D50-5 (+B) - Body ground | Ignition switch ON | 11 to 14 V (near battery voltage) |
| D52-1 (BAT2) - Body ground | Always | 11 to 14 V (near battery voltage) |
| D54-5 (+B2) - Body ground | Ignition switch ON | 11 to 14 V (near battery voltage) |
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER) |
Disconnect the D74 ECM connector.
Disconnect the D50 or D54 AID connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D74-54 (AIRP) - D50-4 (SIP) | Always | Below 1 Ω |
| D74-53 (ARP2) - D54-4 (SIP2) | Always | Below 1 Ω |
| D74-54 (AIRP) or D50-4 (SIP) - body ground | Always | 10 kΩ or higher |
| D74-53 (ARP2) or D54-4 (SIP2) - body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 14.INSPECT AIR PUMP ASSEMBLY (BANK 1 OR BANK 2) |
![]() |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the 400 A probe of an ammeter to the positive (+) wire of the air pump.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.
Measure the current while the air pump is on and off.
| Tester Operation | Air Pump | ASV | Specified Condition |
| AIR PUMP: ON, ASV: OPEN | ON | OPEN | 10 to 40 A |
| AIR PUMP: OFF, ASV: CLOSE | OFF | CLOSE | Below 1 A |
|
| ||||
| OK | |
| 15.PERFORM ACTIVE TEST USING TECHSTREAM |
![]() |
Disconnect the AID connectors.
Connect terminals DI and SIV or DI2 and SIV2 of the wire harness connector for the AID.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN or AIR PUMP 2: ON, ASV 2: OPEN.
Start the engine.
Perform the AIR system forced operation while the engine is idling.
Measure the voltage between the SIV and E or SIV2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.
Turn the ignition switch off.
| Tester Connection | Condition | Specified Condition |
| D50-3 (SIV) - D50-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| D54-3 (SIV2) - D54-1 (E2) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| D50-3 (SIV) - D50-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
| D54-3 (SIV2) - D54-1 (E2) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
![]() |
Connect terminals DI and SIP or DI2 and SIP2 of the wire harness connector for the AID.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN or AIR PUMP 2: ON, ASV 2: OPEN.
Start the engine.
Perform the AIR system forced operation while the engine is idling.
Measure the voltage between the SIP and E or SIP2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.
Turn the ignition switch off.
| Tester Connection | Condition | Specified Condition |
| D50-4 (SIP) - D50-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| D54-4 (SIP2) - D54-1 (E2) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| D50-4 (SIP) - D50-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
| D54-4 (SIP2) - D54-1 (E2) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
|
| ||||
| OK | |
| 16.REPLACE AIR INJECTION CONTROL DRIVER |
Replace the air injection control driver (Click here).
| NEXT | |
| 17.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2447) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (if set) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Air injection check / Automatic Mode.
Start the engine after the Techstream initialization is finished.
Perform the System Check operation by pressing Next.
After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.
Check pending DTCs.
Turn the ignition switch off.
|
| ||||
| OK | ||
| ||