Home › DRIVE LINE › DRIVE SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for 4WD)

FRONT DRIVE SHAFT ASSEMBLY (for 4WD) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH (for Front Differential Side)
  1. Install a new snap ring to the inboard joint shaft.

  1. Coat the spline of the inboard joint shaft assembly with gear oil.



    C160578
  1. Align the shaft splines and install the drive shaft with a brass bar and hammer.

    NOTICE:
    1. Set the snap ring with the opening side facing downward.
    2. Be careful not to damage the oil seal.

    HINT:
    Whether the inboard joint shaft is in contact with the pinion shaft or not can be confirmed from the sound or feeling when driving it.



2. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH (for Axle Hub Side)
  1. Install the drive shaft to the steering knuckle.

    NOTICE:
    Be careful not to damage the oil seal, boots and dust seal.



3. CONNECT FRONT LOWER BALL JOINT ATTACHMENT


C155985
  1. Connect the attachment to the steering knuckle with the 2 bolts.

    Torque:
    300 N*m{ 3059 kgf*cm , 221 ft.*lbf }



4. INSTALL TIE ROD END SUB-ASSEMBLY
  1. Connect the tie rod end LH to the steering knuckle with the nut.

    Torque:
    69 N*m{ 704 kgf*cm , 51 ft.*lbf }

  1. Install a new cotter pin.

    HINT:
    Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.



5. INSTALL AXLE HUB NUT
  1. Clean the threaded parts on the drive shaft and axle hub nut using a non-residue solvent.

    NOTICE:
    1. Be sure to perform this work for a new drive shaft.
    2. Keep the threaded parts free of oil and foreign objects.

  1. Using a 39 mm socket wrench, install the hub nut.

    Torque:
    338 N*m{ 3446 kgf*cm , 249 ft.*lbf }



    C159318
  1. Install the front wheel adjusting lock cap and a new cotter pin.



6. INSTALL FRONT AXLE HUB GREASE CAP
  1. Install the axle hub grease cap.

    NOTICE:
    Make sure to securely fit the bearing to the axle hub.



7. INSTALL FRONT SPEED SENSOR LH
  1. Install the front speed sensor (Click here).



8. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover to the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    Torque:
    for bolt:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    for screw:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



9. INSTALL FRONT WHEEL
  1. Install the front wheels.

    Torque:
    for aluminum wheel:
    131 N*m{ 1336 kgf*cm , 97 ft.*lbf }
    for steel wheel:
    209 N*m{ 2131 kgf*cm , 154 ft.*lbf }



10. ADD DIFFERENTIAL OIL


    D025304E27
  1. Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. Too much or too little oil will lead to differential problems.
    2. After changing the oil, drive the vehicle and then check the oil level again.

    Oil type:
    Item
    Oil type and viscosity
    Front differential
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent.
    Rear differential

    Front differential capacity:
    Specified Condition
    2.00 to 2.10 liters (2.12 to 2.21 US qts., 1.76 to 1.84 Imp. qts.)


    Rear differential capacity:

    Engine type
    Wheelbase type
    Cab type
    Drive type
    Specified Condition
    3UR-FE. 3UR-FBE
    3220 mm (10 ft. 6.8 in.)
    Regular
    2WD
    3.45 to 3.55 liters (3.65 to 3.75 US qts., 3.04 to 3.12 Imp. qts.)
    4WD
    3700 mm (12 ft. 1.7 in.)
    Regular
    2WD
    3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.)
    4WD
    Double
    2WD
    4WD
    CrewMax
    2WD
    3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.)
    4WD
    3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.)
    4180 mm (13 ft. 8.6 in.)
    Double
    2WD
    3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.)
    4WD
    1GR-FE and 1UR-FE
    3220 mm (10 ft. 6.8 in.)
    Regular
    2WD
    4.00 to 4.10 liters (4.23 to 4.33 US qts., 3.52 to 3.60 Imp. qts.)
    4WD
    3700 mm (12 ft. 1.7 in.)
    ALL
    2WD
    4.55 to 4.65 liters (4.81 to 4.91 US qts., 4.01 to 4.09 Imp. qts.)
    4WD
    4180 mm (13 ft. 8.6 in.)
    2WD
    4WD

  1. for Rear Differential:

    1. Install a new gasket and the filler plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. for Front Differential:

    1. Using a 10 mm hexagon wrench, install a new gasket and the filler plug.

      Torque:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }



11. CHECK SPEED SENSOR SIGNAL
  1. Check the speed sensor signal .



12. CHECK FOR DIFFERENTIAL OIL LEAK


13. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
  1. Inspect and adjust the front wheel alignment (Click here).