Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > INSTALLATION

for Preparation Click here



1. INSTALL AIR CONDITIONING UNIT


  1. Install the air conditioning unit with the nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



    E146042



2. INSTALL REAR NO. 1 AIR DUCT (except Regular Cab)
  1. Attach the 7 claws to install the rear No. 1 air duct.



3. INSTALL REAR NO. 3 AIR DUCT (except Regular Cab)
  1. Attach the 7 claws to install the rear No. 3 air duct.



4. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY


  1. Install the instrument panel reinforcement assembly.


    E281067E01


    Text in Illustration 
    *1
    ''TORX'' Bolt
    *2
    Collar

    1. Temporarily install the instrument panel reinforcement assembly.

    2. for Passenger Side:
      Using a 12 mm hexagon wrench, install the 2 collars.

    3. for Passenger Side:
      Using a T40 "TORX" socket, install the 2 "TORX" bolts.

      Torque:
      18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    4. for Driver Side:
      Install the 3 bolts and 2 caps.

  1. Attach the clamps and connectors to connect the wire harness.



  1. Install the 11 bolts and 4 nuts.


    E281066E01

    HINT:
    Tighten the bolt in the order shown in the illustration to install the instrument panel reinforcement assembly to the air conditioning unit.



5. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
for Column Shift Type:
for Floor Shift Type:


6. INSTALL STEERING COLUMN ASSEMBLY
(Click here)


7. INSTALL FRONT WIPER MOTOR AND BRACKET
(Click here)


8. CONNECT INLET HEATER WATER HOSE AND OUTLET HEATER WATER HOSE


    E281050E01
  1. Connect the inlet heater water hose and outlet heater water hose with the paint mark facing right and attach the clip shown in the illustration.
    Text in Illustration 
    *A
    for 1GR-FE
    *B
    for UR Engine Series
    *a
    Paint Mark (Green)
    *b
    Paint Mark (Blue)
    *c
    Paint Mark (Yellow)
    *d
    Paint Mark (White)



9. CONNECT SUCTION PIPE SUB-ASSEMBLY AND AIR CONDITIONER TUBE ASSEMBLY


    E142174E02
  1. Remove the attached vinyl tape from the tubes.

  1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the suction pipe sub-assembly and air conditioner tube assembly.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 2 O-rings to the suction pipe sub-assembly and air conditioner tube assembly.

  1. Connect the suction pipe sub-assembly and air conditioner tube assembly.

    HINT:
    After the connection, check that the claw of the piping clamp is engaged.

  1. Attach the plate as shown in the illustration and install the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

    Text in Illustration 
    *1
    Plate



10. INSTALL NO. 2 COOLER COVER


    E146043
  1. Attach the 2 claws to install the No. 2 cooler cover.

  1. Install the 2 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



12. CHECK SRS WARNING LIGHT
(Click here)


13. ADD ENGINE COOLANT
for 1GR-FE:
for 1UR-FE:
for 3UR-FE:
for 3UR-FBE:


14. CHARGE REFRIGERANT
SST
09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02090, 09985-02110, 09985-02130, 09985-02150)
  1. Perform vacuum purging using a vacuum pump.



  1. Charge refrigerant HFC-134a (R134a).

    Standard:
    600 +/-30 g (21.2 +/-1.1 oz.)



    I037365E29


    Text in Illustration 
    *a
    Amount to be charged
    *b
    Charge 200 g (7.05 oz.)
    *c
    Mean value in proper range
    *d
    Point where bubbles disappear
    *e
    Overcharged
    *f
    High Pressure
    *g
    Sub-cool System
    *h
    Refrigerant Amount

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor will not work properly without any refrigerant, and will overheat.
    2. Approximately 200 g (7.05 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by measuring its quantity, and not with the sight glass.



15. WARM UP ENGINE
  1. Warm up the engine at less than 1500 rpm for 1 minute or more after charging the refrigerant.

    NOTICE:
    Be sure to warm up the compressor when turning the A/C switch ON after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.



16. CHECK FOR ENGINE COOLANT LEAK
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation under the following conditions:

    1. The ignition switch is OFF.
    2. The vehicle is in a place with good air ventilation and without any volatile gases, such as evaporated gasoline or exhaust gas. The detector is very sensitive to volatile gases.
    3. Some refrigerant is remaining in the refrigerant system.
    4. The compressor is off and its pressure is approximately 392 to 588 kPa (4.0 to 6.0 kgf/cm2, 57 to 85 psi).



    I042222E42
  1. Using a halogen leak detector, check the refrigerant line for leakage.
    Text in Illustration 
    *1
    Halogen Leak Detector
    *a
    Inspect for leak

  1. If a gas leak is not detected on the drain hose, remove the blower motor control (blower resistor) from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the connector and wait for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.



17. CHECK FOR REFRIGERANT GAS LEAK