Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > REMOVAL

for Preparation Click here



1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. Turn the A/C switch ON.

  1. Operate the cooler compressor with an engine speed of approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the compressor oil remaining in each component into the cooler compressor.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.



2. DRAIN ENGINE COOLANT
for 1GR-FE:
for 1UR-FE:
for 3UR-FE:
for 3UR-FBE:


3. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



5. REMOVE NO. 2 COOLER COVER


E146043
  1. Remove the 2 nuts.

  1. Detach the 2 claws and remove the No. 2 cooler cover.



6. DISCONNECT SUCTION PIPE SUB-ASSEMBLY AND AIR CONDITIONER TUBE ASSEMBLY


    E142173E02
  1. Remove the bolt.

  1. Detach the plate as shown in the illustration.
    Text in Illustration 
    *1
    Plate

  1. Disconnect the suction pipe sub-assembly and air conditioner tube assembly.

    NOTICE:
    1. Do not use a screwdriver or similar tool to disconnect the tube.
    2. Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

  1. Remove the 2 O-rings from the suction pipe sub-assembly and liquid tube.



7. DISCONNECT INLET HEATER WATER HOSE AND OUTLET HEATER WATER HOSE


    E281049E01
  1. Using pliers, grip the claws of the clip and slide the clip.
    Text in Illustration 
    *A
    for 1GR-FE
    *B
    for UR Engine Series

  1. Disconnect the inlet heater water hose and outlet heater water hose.



8. REMOVE FRONT WIPER MOTOR AND BRACKET
(Click here)


9. REMOVE STEERING COLUMN ASSEMBLY
(Click here)


10. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
for Column Shift Type:
for Floor Shift Type:


11. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
  1. Disconnect the clamps, connectors and wire harness.



  1. Remove the 11 bolts and 4 nuts.


    E281066



  1. Remove the instrument panel reinforcement assembly.



    1. for Driver Side:
      Remove the 2 caps and 3 bolts.


      E281068E01


      Text in Illustration 
      *1
      'TORX' Bolt
      *2
      Collar

    2. for Passenger Side:
      Using a T40 "TORX" socket, remove the 2 "TORX" bolts.

      HINT:
      When removing the bolts, the collars may come off with the bolts.

    3. for Passenger Side:
      Using a 12 mm hexagon wrench, remove the 2 collars.



12. REMOVE REAR NO. 1 AIR DUCT (except Regular Cab)


    E281033
  1. Detach the 7 claws and remove the rear No. 1 air duct.



13. REMOVE REAR NO. 3 AIR DUCT (except Regular Cab)


    E281032
  1. Detach the 7 claws and remove the rear No. 3 air duct.



14. REMOVE AIR CONDITIONING UNIT


  1. Remove the nut and air conditioning unit.


    E146042