Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › CONDENSER

CONDENSER > INSTALLATION

for Preparation Click here



1. INSTALL COOLER DRYER


    E050386E01
  1. Using pliers, install the cooler dryer.



    E055408E01
  1. Apply a sufficient amount of compressor oil to the contact surfaces of a new O-ring and the cap.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring to the cap.



    I030086E01
  1. Using a 14 mm hexagon socket wrench, install the cap to the modulator.

    Torque:
    2.9 N*m{ 30 kgf*cm , 26 in.*lbf }



2. INSTALL COOLER CONDENSER ASSEMBLY


    E283114E01
  1. Install the cooler condenser assembly with the 2 bolts as shown in the illustration.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

    Text in Illustration 
    *A
    w/o Air Cooled Transmission Oil Cooler
    *B
    w/ Air Cooled Transmission Oil Cooler



3. CONNECT AIR CONDITIONER TUBE ASSEMBLY
  1. Remove the attached vinyl tape from the air conditioner tube assembly and the connecting part of the cooler condenser assembly.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the pipe joint.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring to the air conditioner tube assembly.

  1. Connect the air conditioner tube assembly to the cooler condenser assembly with the 2 bolts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

    NOTICE:
    1. When tightening the bolt, do not allow any tools to contact the pipe.
    2. When tightening the bolt, hold a part of the pipe near the connector.



4. CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
  1. Remove the attached vinyl tape from the No. 1 cooler refrigerant discharge hose and the connecting part of the cooler condenser assembly.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the hose joint.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring to the No. 1 cooler refrigerant discharge hose.

  1. Connect the No. 1 cooler refrigerant discharge hose to the cooler condenser assembly with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

    NOTICE:
    1. When tightening the bolt, do not allow any tools to contact the pipe.
    2. When tightening the bolt, hold a part of the pipe near the connector.



5. INSTALL RADIATOR ASSEMBLY
for 1GR-FE: (Click here)
for 1UR-FE:
for 3UR-FE: (Click here)
for 3UR-FBE: (Click here)


6. CONNECT OIL COOLER HOSE (w/ Air Cooled Transmission Oil Cooler)


    E281055E01
  1. Connect the 2 oil cooler hoses and attach the 2 clips.

    NOTICE:
    Make sure the paint marks and pinching portion of each clip are facing the directions shown in the illustration.

    Text in Illustration 
    *1
    Blue Paint
    *2
    Pink Paint



7. INSTALL FRONT BUMPER COVER
(Click here)


8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



9. CHARGE REFRIGERANT
SST
09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02090, 09985-02110, 09985-02130, 09985-02150)
  1. Perform vacuum purging using a vacuum pump.



  1. Charge refrigerant HFC-134a (R134a).

    Standard:
    600 +/-30 g (21.2 +/-1.1 oz.)



    I037365E29


    Text in Illustration 
    *a
    Amount to be charged
    *b
    Charge 200 g (7.05 oz.)
    *c
    Mean value in proper range
    *d
    Point where bubbles disappear
    *e
    Overcharged
    *f
    High Pressure
    *g
    Sub-cool System
    *h
    Refrigerant Amount

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor will not work properly without any refrigerant, and will overheat.
    2. Approximately 200 g (7.05 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by measuring its quantity, and not with the sight glass.



10. WARM UP ENGINE
  1. Warm up the engine at less than 1500 rpm for 1 minute or more after charging the refrigerant.

    NOTICE:
    Be sure to warm up the compressor when turning the A/C switch ON after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.



11. CHECK FOR REFRIGERANT GAS LEAK
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation under the following conditions:

    1. The ignition switch is OFF.
    2. The vehicle is in a place with good air ventilation and without any volatile gases, such as evaporated gasoline or exhaust gas. The detector is very sensitive to volatile gases.
    3. Some refrigerant is remaining in the refrigerant system.
    4. The compressor is off and its pressure is approximately 392 to 588 kPa (4.0 to 6.0 kgf/cm2, 57 to 85 psi).



    I042222E42
  1. Using a halogen leak detector, check the refrigerant line for leakage.
    Text in Illustration 
    *1
    Halogen Leak Detector
    *a
    Inspect for leak

  1. If a gas leak is not detected on the drain hose, remove the blower motor control (blower resistor) from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the connector and wait for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.



12. CHECK SRS WARNING LIGHT
(Click here)