Home › ENGINE · 1UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0107    Manifold Absolute Pressure / Barometric Pressure Circuit Low Input

DTC    P0108    Manifold Absolute Pressure / Barometric Pressure Circuit High Input

for Preparation Click here


DESCRIPTION

By a built-in sensor unit, the manifold absolute pressure sensor detects the intake manifold pressure as a voltage.
A207508E01

DTC No.
DTC Detection Condition
Trouble Area
P0107
The manifold absolute pressure sensor voltage is below 0.5 V for 0.5 seconds.
(1 trip detection logic)
  1. Open or short in manifold absolute pressure sensor circuit
  2. Manifold absolute pressure sensor
  3. ECM
P0108
The manifold absolute pressure sensor voltage is higher than 4.5 V for 0.5 seconds.
(1 trip detection logic)
  1. Open or short in manifold absolute pressure sensor circuit
  2. Manifold absolute pressure sensor
  3. ECM

HINT:
When any of these DTCs are output, check the manifold absolute pressure using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.


MAP
Malfunction
Approximately 0 kPa
  1. Short in PIM circuit to ground
  2. Open in VC circuit
130 kPa or higher
  1. Short in VC circuit to PIM circuit
  2. Open in PIM circuit
  3. Open in E2 circuit

MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the manifold absolute pressure. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the manifold pressure sensor and sets a DTC.
Example:
When the sensor output voltage remains less than 0.5 V, or more than 4.5 V for more than 0.5 seconds, the ECM sets a DTC.
If the malfunction is not repaired successfully, a DTC is set 0.5 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0107: Manifold Absolute Pressure (MAP) sensor range check (Low voltage)
P0108: Manifold Absolute Pressure (MAP) sensor range check (High voltage)
Required Sensors/Components (Main)
Manifold absolute pressure sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Starter
Off
Battery voltage
8 V or more
Ignition switch
On (IG)
Time after starter ON to OFF
2 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


P0107 
MAP sensor voltage
Below 0.5 V

P0108 
MAP sensor voltage
Higher than 4.5 V

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine.
  7. Idle the engine for 5 seconds [A].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0107 or P0108.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A165731E25


INSPECTION PROCEDURE

HINT:
  1. If DTCs relating to different systems are stored and they share terminal E2 as their ground, check this ground circuit first.
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (MANIFOLD ABSOLUTE PRESSURE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.

  1. Read the MAP value.

    OK:
    Same value as the actual atmospheric pressure.

    HINT:
    1. Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather (high atmospheric pressure, low atmospheric pressure).
    2. Also, check "Atmosphere Pressure" in the Data List.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR (TERMINAL VOLTAGE)


    A217923E02
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D80-3 (VC) - D80-2 (E2)
    Ignition switch ON
    4.5 to 5.5 V
    D80-1 (PIM) - D80-2 (E2)
    Ignition switch ON
    3.0 to 5.0 V



NG
Go to step 5
OK


3.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Replace the manifold absolute pressure sensor (Click here).


NEXT


4.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and wait for 2 seconds.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Display (DTC output)
    Proceed to
    No DTC output
    A
    DTC P0107 and/or P0108 output
    B



B
REPLACE ECM (Click here)
A

END 

5.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)


    A217924E02
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    D80-1 (PIM) - D74-97 (PIM)
    Always
    Below 1 Ω
    D80-3 (VC) - D74-66 (VCV2)
    Always
    Below 1 Ω
    D80-2 (E2) - D74-98 (E2)
    Always
    Below 1 Ω

    Standard Resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D80-1 (PIM) or D74-97 (PIM) - Body ground
    Always
    10 kΩ or higher
    D80-3 (VC) or D74-66 (VCV2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)