AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION |
| 1. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY |
![]() |
Using a vernier caliper and straightedge, measure dimension "A" between the transmission fitting surface of the engine*1 and the torque converter fitting surface of the drive plate*2 (step 1).
![]() |
Align the matchmarks on the transmission case and torque converter clutch, and then mesh the splines of the input shaft and turbine runner.
| *a | Matchmark |
![]() |
Mesh the splines of the stator shaft and stator while turning the torque converter clutch.
| *a | Matchmark |
![]() |
Turn the torque converter clutch and align the matchmarks on the torque converter clutch and transmission case to fit the key of the oil pump drive gear into the slot on the torque converter clutch.
| *a | Matchmark |
![]() |
Using a vernier caliper and straightedge, measure dimension "B" shown in the illustration and check that B is more than A (measured in step 1).
| 2. INSTALL TRANSMISSION CONTROL CABLE BRACKET |
Install the bracket with the 2 bolts.
| 3. INSTALL WIRE HARNESS CLAMP BRACKET |
![]() |
Install the 5 wire harness clamp brackets with the 5 bolts.
| 4. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY |
![]() |
Apply clutch spline grease to the surface of the torque converter centerpiece that contacts the crankshaft.
| *1 | Torque Converter Centerpiece |
| *2 | Crankshaft |
![]() |
Confirm that the 2 knock pins are on the transmission contact surface of the engine block before transmission installation.
Install the transmission with the 10 bolts.
| 5. INSTALL TRANSMISSION OIL COOLER ASSEMBLY |
![]() |
Coat 2 new O-rings with ATF and install them to the grooves of the transmission oil cooler.
Install the transmission oil cooler to the transmission oil cooler spacer with the 3 bolts.
![]() |
Install the 2 No. 1 transmission oil cooler hoses to the transmission oil cooler spacer.
Connect the 2 No. 1 transmission oil cooler hoses to the transmission.
Temporarily install the transmission oil cooler together with the transmission oil cooler spacer with bolt C. Temporarily install bolt A and bolt B. Tighten the bolts in alphabetical order.
| 6. CONNECT WATER BY-PASS PIPE |
![]() |
Connect the 2 water by-pass hoses to the transmission oil cooler and connect the water by-pass pipe with the bolt.
| *a | Yellow Paint Mark |
| *b | White Paint Mark |
| 7. CONNECT WIRE HARNESS AND CONNECTOR |
Connect the park/neutral position switch connector, transmission wire connector and 2 speed sensor connectors.

Connect the harness clamp with the bolt.
Attach the 4 connector clamps and 5 harness clamps.
Tilt up the automatic transmission.
Connect the ground cable with the bolt.
| 8. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR |
Install the rear engine mounting insulator to the transmission with the 4 bolts.
| 9. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.
Install the frame crossmember with the 4 bolts, 4 washers and 4 nuts.
| 10. INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT |
Turn the crankshaft to gain access to the installation locations of the 6 torque converter clutch setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.
Install the flywheel housing side cover.
| 11. INSTALL STARTER ASSEMBLY |
| 12. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Connect the control cable with a new clip and the nut.
| *1 | Bracket |
| *a | Inside of Vehicle |
| 13. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
| 14. INSTALL PROPELLER SHAFT ASSEMBLY |
| 15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 16. ADD AUTOMATIC TRANSMISSION FLUID |
| 17. ADD ENGINE COOLANT |
Add engine coolant.
![]() |
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
Install the radiator cap.
Start the engine and warm it up until the thermostat opens.
Maintain the engine speed at 2000 to 2500 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines.
If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 18. CHECK FOR ENGINE COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 19. ADJUST SHIFT LEVER POSITION (for Column Shift Type) |
Move the shift lever to N.
![]() |
Fold back the transmission control cable adjust case cover. Then while sliding the slider toward the cable end side, press out the lock piece from the back side to release the lock.
![]() |
Check that the spring of the adjust case is applying enough tension to the shift control cable. Then press in the lock piece to set the lock.
Return the cover of the adjust case to its original position.
Inspect the shift lever operation after the adjustment.
| 20. ADJUST SHIFT LEVER POSITION (for Floor Shift Type) |
Move the shift lever to N.
![]() |
Fold back the transmission control cable adjust case cover. Then while sliding the slider toward the cable end side, press out the lock piece from the back side to release the lock.
| *1 | Lock Piece |
| *2 | Slider |
![]() |
Check that the spring of the adjust case is applying enough tension to the shift control cable. Then press in the lock piece to set the lock.
| *1 | Lock Piece |
| *2 | Slider |
Return the cover of the adjust case to its original position.
Inspect the shift lever operation after the adjustment.
| 21. INSPECT SHIFT LEVER POSITION (for Column Shift Type) |
When moving the shift lever from N to other positions, check that the lever can be moved smoothly and accurately to each position and that the position indicator comes on in accordance with the shift lever position.
If the indicator and shift lever position do not match, carry out the following adjustment procedures.
| 22. INSPECT SHIFT LEVER POSITION (for Floor Shift Type) |
When moving the shift lever from N to other positions, check that the lever can be moved smoothly and accurately to each position and that the position indicator comes on in accordance with the shift lever position.
If the indicator and shift lever position do not match, carry out the following adjustment procedures.
| 23. INSPECT FOR EXHAUST GAS LEAK |
| 24. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Hook the engine under cover to the vehicle body as shown in the illustration.
Install the 3 screws and 5 bolts.
| 25. RESET MEMORY |