SFI SYSTEM > ECM Power Source Circuit |

| 1.INSPECT FUSES (AM2, IG2 MAIN, EFI NO. 1, IGN) |
![]() |
Remove the AM2 fuse, IG2 MAIN fuse, EFI NO. 1 fuse and IGN fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| AM2 fuse | Always | Below 1 Ω |
| IG2 MAIN fuse | Always | Below 1 Ω |
| EFI NO. 1 fuse | Always | Below 1 Ω |
| IGN fuse | Always | Below 1 Ω |
|
| ||||
| OK | |
| 2.INSPECT INTEGRATION RELAY (IG2, EFI) |
![]() |
Remove the integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1C-1 - 1B-8 | No battery voltage is applied to terminals 1B-6 and 1B-7 | 10 kΩ or higher |
| 1C-1 - 1B-8 | Battery voltage is applied to terminals 1B-6 and 1B-7 | Below 1 Ω |
| 1C-1 - 1B-4 | No battery voltage is applied to terminals 1B-2 and 1B-3 | 10 kΩ or higher |
| 1C-1 - 1B-4 | Battery voltage is applied to terminals 1B-2 and 1B-3 | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) |
![]() |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D74-81 (E1) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.INSPECT ECM (IGSW VOLTAGE) |
![]() |
Disconnect the ECM connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A24-28 (IGSW) - D74-81 (E1) | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (RELAY BLOCK - ECM, IGNITION SWITCH, BATTERY AND BODY GROUND) |
![]() |
Disconnect the ECM connector.
Disconnect the ignition switch connector.
Disconnect the cable from the battery negative (-) terminal.
Disconnect the cable from the battery positive (+) terminal.
Remove the AM2 fuse and integration relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A24-28 (IGSW) - 1B-8 | Always | Below 1 Ω |
| 1B-7 - Body ground | Always | Below 1 Ω |
| Positive (+) battery cable - 1C-1 | Always | Below 1 Ω |
| Positive (+) battery cable - AM2 fuse terminal 1 | Always | Below 1 Ω |
| J9-5 (AM2) - AM2 fuse terminal 2 | Always | Below 1 Ω |
| J9-6 (IG2) - 1B-6 | Always | Below 1 Ω |
| A24-28 (IGSW) or 1B-8 - Body ground | Always | 10 kΩ or higher |
| Positive (+) battery cable or 1C-1 - Body ground | Always | 10 kΩ or higher |
| Positive (+) battery cable or AM2 fuse terminal 1 - Body ground | Always | 10 kΩ or higher |
| J9-5 (AM2) or AM2 fuse terminal 2 - Body ground | Always | 10 kΩ or higher |
| J9-6 (IG2) or 1B-6 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.INSPECT IGNITION SWITCH |
Inspect the ignition switch (Click here).
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM, BATTERY AND BODY GROUND) |
![]() |
Disconnect the ECM connector.
Disconnect the cable from the battery negative (-) terminal.
Disconnect the cable from the battery positive (+) terminal.
Remove the integration relay from the engine room relay block.
Disconnect the integration relay connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A24-3 (+B) - 1B-4 | Always | Below 1 Ω |
| A24-2 (+B2) - 1B-4 | Always | Below 1 Ω |
| A24-34 (MREL) - 1B-2 | Always | Below 1 Ω |
| 1C-1 - Positive (+) battery cable | Always | Below 1 Ω |
| 1B-3 - Body ground | Always | Below 1 Ω |
| A24-3 (+B) or 1B-4 - Body ground | Always | 10 kΩ or higher |
| A24-2 (+B2) or 1B-4 - Body ground | Always | 10 kΩ or higher |
| A24-34 (MREL) or 1B-2 - Body ground | Always | 10 kΩ or higher |
| 1C-1 or Positive (+) battery cable - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||