Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM (for Navigation Receiver Type)

REAR VIEW MONITOR SYSTEM (for Navigation Receiver Type) > Image from Camera for Rear View Monitor is Abnormal

for Preparation Click here


DESCRIPTION

This is the display signal circuit between the navigation receiver assembly and the television camera assembly.

WIRING DIAGRAM


E224828E14


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the J136 navigation receiver assembly connector.

  1. Disconnect the X1 television camera assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J136-11 (CA+) - X1-6 (CB+)
    Always
    Below 1 Ω
    J136-12 (V+) - X1-3 (CV+)
    Always
    Below 1 Ω
    J136-23 (CGND) - X1-5 (CGND)
    Always
    Below 1 Ω
    J136-24 (V-) - X1-2 (CV-)
    Always
    Below 1 Ω
    J136-11 (CA+) - Body ground
    Always
    10 kΩ or higher
    J136-12 (V+) - Body ground
    Always
    10 kΩ or higher
    J136-23 (CGND) - Body ground
    Always
    10 kΩ or higher
    J136-24 (V-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK NAVIGATION RECEIVER ASSEMBLY


    E280624E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J136-23 (CGND) - Body ground
    Always
    Below 1 Ω
    J136-24 (V-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Navigation Receiver Assembly)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Column Shift Type)
    B
    NG (for Floor Shift Type)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
A


3.CHECK NAVIGATION RECEIVER ASSEMBLY


    E263040E02
  1. Disconnect the television camera assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    X1-6 (CB+) - X1-5 (CGND)
    Ignition switch ACC
    5.5 to 7.05 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Television Camera Assembly)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Column Shift Type)
    B
    NG (for Floor Shift Type)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
A


4.CHECK TELEVISION CAMERA ASSEMBLY


  1. Using an oscilloscope, check the waveform.


    E275625E05


    Text in Illustration 
    *a
    Component with harness connected
    (Navigation Receiver Assembly)
    *b
    Waveform 1
    *c
    Waveform 2
    *d
    Synchronized Signal
    *e
    Video Waveform
    -
    -
    Measurement Condition 
    Item
    Content
    Tester Connection
    J136-12 (V+) - J136-24 (V-)
    Tool Setting
    0.2 V/DIV., 50 μs/DIV.
    Condition
    1. Waveform 1: Ignition switch ON
    2. Waveform 2: Ignition switch ON, screen blacked out by covering camera lens

    OK:
    Waveform is as shown in illustration.

    HINT:
    The video waveform changes according to the image sent by the television camera assembly.



NG
REPLACE TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)