FRONT DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL (for 4WD) > REPLACEMENT |
| 1. DRAIN DIFFERENTIAL OIL |
Stop the vehicle on a level place.
for Front Differential:
Using a 10 mm hexagon wrench, remove the filler plug and gasket.
Using a 10 mm hexagon wrench, remove the drain plug and gasket, and drain the oil.
Using a 10 mm hexagon wrench, install a new gasket and the drain plug.
for Rear Differential:
Remove the filler plug and gasket.
Remove the drain plug and gasket, and drain the oil.
Install a new gasket and the drain plug.
| 2. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH |
Remove the front drive shaft (Click here).
| 3. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL |
![]() |
Using SST, tap out the 2 oil seals.
| 4. INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL |
![]() |
Apply MP grease to 2 new oil seals.
Using SST and a hammer, tap in the 2 oil seals.
| Side | Specified Condition |
| LH | -0.45 to 0.45 mm (-0.0177 to 0.0177 in.) |
| RH | 4.8 to 5.8 mm (0.189 to 0.228 in.) |
| 5. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH |
Install the front drive shaft (Click here).
| 6. ADD DIFFERENTIAL OIL |
![]() |
Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.
| Item | Oil type and viscosity |
| Front differential | Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent. |
| Rear differential |
| Specified Condition | |
| 2.00 to 2.10 liters (2.12 to 2.21 US qts., 1.76 to 1.84 Imp. qts.) |
| Engine type | Wheelbase type | Cab type | Drive type | Specified Condition |
| 3UR-FE. 3UR-FBE | 3220 mm (10 ft. 6.8 in.) | Regular | 2WD | 3.45 to 3.55 liters (3.65 to 3.75 US qts., 3.04 to 3.12 Imp. qts.) |
| 4WD | ||||
| 3700 mm (12 ft. 1.7 in.) | Regular | 2WD | 3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.) | |
| 4WD | ||||
| Double | 2WD | |||
| 4WD | ||||
| CrewMax | 2WD | 3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.) | ||
| 4WD | 3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.) | |||
| 4180 mm (13 ft. 8.6 in.) | Double | 2WD | 3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.) | |
| 4WD | ||||
| 1GR-FE and 1UR-FE | 3220 mm (10 ft. 6.8 in.) | Regular | 2WD | 4.00 to 4.10 liters (4.23 to 4.33 US qts., 3.52 to 3.60 Imp. qts.) |
| 4WD | ||||
| 3700 mm (12 ft. 1.7 in.) | ALL | 2WD | 4.55 to 4.65 liters (4.81 to 4.91 US qts., 4.01 to 4.09 Imp. qts.) | |
| 4WD | ||||
| 4180 mm (13 ft. 8.6 in.) | 2WD | |||
| 4WD |
for Rear Differential:
Install a new gasket and the filler plug.
for Front Differential:
Using a 10 mm hexagon wrench, install a new gasket and the filler plug.