Home › ENGINE ยท 1GR-FE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


2. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



4. REMOVE RADIATOR GRILLE SUB-ASSEMBLY


5. REMOVE HOOD SUB-ASSEMBLY
  1. Remove the 4 bolts, 2 clips and hood.



6. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY
(Click here)


7. REMOVE FRONT COWL TOP OUTER PANEL SUB-ASSEMBLY
  1. Disconnect the washer hose.



  1. Remove the 7 bolts and front cowl top outer panel.


    A151796



8. REMOVE FRONT FENDER APRON SEAL LH
  1. Remove the 6 clips and front fender apron seal.



9. REMOVE FRONT FENDER APRON SEAL RH
  1. Remove the 6 clips and front fender apron seal.



10. REMOVE FRONT FENDER APRON SEAL REAR LH
  1. Remove the 5 clips and fender apron seal.



11. REMOVE FRONT FENDER APRON SEAL REAR RH
  1. Remove the 5 clips and fender apron seal.



12. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



13. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs.


    A237558E01


    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Radiator Cap
    *3
    Radiator Drain Cook Plug
    *4
    Cylinder Block Drain Cock Plug

  1. Remove the radiator cap. Then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain cock plug by hand.



14. REMOVE AIR CLEANER CAP AND HOSE


    A239075
  1. Remove the air cleaner cap and hose.

    1. Disconnect the mass air flow meter connector, vacuum hose and ventilation hose and detach the 4 clamps.

    2. Loosen the clamp.

    3. Detach the 4 hook clamps, and then remove the air cleaner cap and hose.



15. REMOVE AIR CLEANER CASE SUB-ASSEMBLY
  1. Remove the air cleaner filter element.



    A239077
  1. Remove the 2 bolts and air cleaner case.



16. REMOVE RADIATOR HOSE INLET


    A238110
  1. Slide the 2 clamps and remove the radiator hose inlet.



17. REMOVE RADIATOR HOSE OUTLET


    A238109
  1. Slide the clamp and disconnect the radiator hose outlet from the water inlet.



    A238108
  1. Slide the clamp and remove the radiator hose outlet from the radiator assembly.



18. REMOVE FAN SHROUD


    A238111
  1. Loosen the 4 nuts holding the fan with fluid coupling.

  1. Remove the fan and generator V-belt (Click here).



    A151755
  1. Disconnect the reservoir hose from the radiator tank upper.

  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fan with fluid coupling, and then remove the fan shroud together with the fan with fluid coupling.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump assembly.



19. REMOVE RADIATOR ASSEMBLY


    A299482
  1. Using a clip remover, remove the 3 clips and disconnect the radiator side deflector RH.



    A299483
  1. Using a clip remover, remove the 3 clips and disconnect the radiator side deflector LH.



    A299479
  1. Remove the 4 bolts and radiator assembly.



20. REMOVE AIR TUBE ASSEMBLY


    A238088
  1. Disconnect the air injection system hose from the air tube assembly.



    A238089
  1. for Bank 1 Side:
    Remove the bolt and disconnect the air tube assembly from the emission control valve set.



    A238087
  1. Disconnect the purge VSV connector.

  1. Detach the 3 wire harness clamps from the intake air surge tank and bracket.

  1. Remove the bolt and wire harness clamp bracket.



    A238090
  1. for Bank 2 Side:
    Remove the 2 bolts and disconnect the air tube assembly from the No. 2 emission control valve set.



21. REMOVE INTAKE AIR SURGE TANK


    A238091
  1. Disconnect the throttle body connector.

  1. Disconnect the No. 4 water by-pass hose.

  1. Disconnect the No. 5 water by-pass hose.



    A238092
  1. Disconnect the No. 1 fuel vapor feed hose.

  1. Disconnect the vacuum hose.

  1. Disconnect the No. 1 ventilation hose.



    A238093
  1. Remove the 2 bolts and throttle body bracket.



    A238094
  1. Using a clip remover, detach the wire harness clamp.



    A238095
  1. Remove the 2 bolts and No. 1 surge tank stay.



    A238096
  1. Remove the 2 bolts and No. 2 surge tank stay.



    A221465
  1. Remove the 2 nuts, 4 bolts and intake air surge tank.

  1. Remove the gasket.



22. REMOVE FAN AND GENERATOR V BELT


    A217571
  1. While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and then insert a bar of 6 mm (0.236 in.) into the service hole to fix the belt tensioner in place.

    HINT:
    The pulley bolt for the belt tensioner has a left-hand thread.

  1. Remove the V belt.



23. DISCONNECT VANE PUMP ASSEMBLY


    A240446
  1. Disconnect the connector.

  1. Detach the wire harness clamp.



    A240447
  1. Remove the 2 bolts and disconnect the vane pump.



24. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector.

  1. Remove the 3 nuts, 2 bolts, exhaust pipe and gasket.



25. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector and detach the 2 clamps.

  1. Remove the 2 bolts.

  1. Remove the 3 nuts, exhaust pipe and 2 gaskets.



26. REMOVE MANIFOLD STAY


    A237695
  1. Remove the 3 bolts and manifold stay.



27. REMOVE AIR TUBE


    A239078
  1. Remove the 2 bolts, 2 nuts and air tube.

  1. Remove the 2 gaskets from the air tube.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.



28. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A237696
  1. Remove the 3 bolts and heat insulator.



29. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A237697
  1. Remove the 6 nuts, manifold and gasket.



30. REMOVE NO. 2 MANIFOLD STAY
  1. Disconnect the wire harness connector.



    A237698
  1. Remove the 3 bolts and No. 2 manifold stay.



31. REMOVE NO. 2 AIR TUBE


    A239085
  1. Remove the 2 bolts, 2 nuts and No. 2 air tube.

  1. Remove the 2 gaskets from the No. 2 air tube.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.



32. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A237699
  1. Remove the 3 bolts and heat insulator.



33. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A237700
  1. Remove the 6 nuts, manifold and gasket.



34. REMOVE GENERATOR ASSEMBLY


    A237638
  1. Remove the bolt and disconnect the wire harness bracket.



    A238033
  1. Open the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Disconnect the generator connector from the generator assembly.



    A237639
  1. Disconnect the wire harness clamp.

  1. Remove the bolt and disconnect the generator bracket.



    A237640
  1. Remove the 2 bolts and generator assembly.



    A222885
  1. Remove the bolt and generator bracket.



35. REMOVE STARTER COVER (for 1.4 kW Type)


    A238034
  1. Remove the 3 bolts and starter cover.



36. REMOVE STARTER ASSEMBLY (for 1.4 kW Type)


    A238035
  1. Remove the bolt and disconnect the ground wire.

  1. Disconnect the starter connector.

  1. Remove the nut and bolt, and then disconnect the starter wire.



    A218197
  1. Remove the 2 bolts and starter.



37. REMOVE STARTER ASSEMBLY (for 1.6 kW Type)


    A238057
  1. Remove the bolt and disconnect the ground wire.

  1. Disconnect the starter connector.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the starter wire.



    A238113
  1. Remove the 2 bolts and starter.



38. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT


C157016
  1. Remove the flywheel housing side cover.



    C157017
  1. Turn the crankshaft to gain access to the 6 bolts and remove each bolt while holding the crankshaft pulley setting bolt with a wrench.



39. DISCONNECT ENGINE WIRE


    A237911
  1. Disconnect the 2 air injection control driver connectors.



    A243486
  1. Detach the 2 wire harness clamps.

  1. Remove the junction block cover.



    A239149
  1. Disconnect the 7 connectors, detach the 2 clamps and disconnect the junction block connector from the junction block.



    A239150
  1. Detach the clamp and disconnect the ECM connector (Click here).



    A239151
  1. Remove the 2 bolts and ground cable.



    A239152
  1. Disconnect the air pump connector and detach the clamp.



    A239153
  1. Remove the bolt, detach the claw and disconnect the engine wire harness.



    A240671
  1. Disconnect the 2 connectors, detach the 2 claws and disconnect the engine room junction block connector from the engine room junction block.



40. DISCONNECT COOLER COMPRESSOR ASSEMBLY
  1. Disconnect the cooler compressor connector.



    A238276
  1. Remove the 2 bolts, 2 nuts and 2 stud bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.



41. DISCONNECT HEATER WATER HOSE ASSEMBLY


A238283
  1. Disconnect the heater water inlet and outlet hoses.



42. DISCONNECT NO. 1 AND NO. 2 FUEL PIPES
  1. Remove the No. 2 fuel pipe clamp from the fuel tube connector.



    A239144
  1. Disconnect the No. 1 and No. 2 fuel pipes (Click here).



43. REMOVE PROPELLER SHAFT ASSEMBLY
(Click here)


44. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
(Click here)


45. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR


C155909

HINT:
Only perform this procedure when replacement of the engine mounting insulator is necessary.

  1. Remove the 4 bolts and rear engine mounting insulator from the transmission.



46. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY


    A224775E01
  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A224777
  1. Remove the 8 bolts, rear spacer, drive plate and front spacer.



47. REMOVE ENGINE ASSEMBLY


    A229669E01
  1. Install 2 engine hangers with 4 bolts as shown in the illustration.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    HINT:
    No. 1 Engine Hanger
    12281-31110
    No. 2 Engine Hanger
    12282-31140
    Bolt
    91671-C0830

  1. Attach an engine sling device and hang the engine with a chain block.



    A237690
  1. Remove the 2 nuts, 4 bolts and front engine mounting insulator LH and RH.

  1. Lift the engine out of the vehicle carefully.
    Text in Illustration 
    V100135
    Nut
    V100136
    Bolt

    NOTICE:
    1. Make sure the engine is clear of all wiring and hoses.
    2. With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
    3. Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.



48. INSTALL ENGINE TO ENGINE STAND
  1. Install the engine to an engine stand with bolts.

  1. Remove the 2 engine hangers and 4 bolts.



49. REMOVE FRONT NO. 2 ENGINE MOUNTING BRACKET LH
  1. Remove the bolt and front No. 2 engine mounting bracket LH.