OIL PUMP > REMOVAL |
| 1. REMOVE ENGINE ASSEMBLY |
| 2. REMOVE EMISSION CONTROL VALVE SET |
![]() |
Disconnect the emission control valve set connector.
Disconnect the air hose from the emission control valve set.
![]() |
Remove the 3 nuts and emission control valve set.
| 3. REMOVE NO. 2 EMISSION CONTROL VALVE SET |
![]() |
Disconnect the No. 2 emission control valve set connector.
Disconnect the air hose.
![]() |
Remove the 3 nuts and No. 2 emission control valve set.
| 4. REMOVE IGNITION COIL ASSEMBLY |
![]() |
Disconnect the 6 ignition coil connectors.
Remove the 6 bolts and 6 ignition coils.
| 5. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE |
![]() |
Remove the dipstick.
Remove the bolt and dipstick guide.
Remove the O-ring from the dipstick guide.
| 6. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY |
![]() |
Disconnect the 2 hoses.
Remove the 3 bolts and water by-pass pipe.
| 7. REMOVE WATER INLET HOUSING |
![]() |
Disconnect the 3 water by-pass hoses.
![]() |
Remove the 5 bolts and water inlet housing.
![]() |
Remove the O-ring and gasket from the water outlet pipe and water pump.
![]() |
Remove the 3 water by-pass hoses.
| 8. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY |
![]() |
Remove the bolt and No. 1 idler pulley.
| 9. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY |
![]() |
for Separate Type:
Remove the 2 bolts, 2 idler pulley cover plates, 2 No. 2 idler pulleys and 2 No. 2 idler pulley cover plates.
| *A | LH |
| *B | RH |
for Integrated Type:
Remove the 2 bolts and 2 No. 2 idler pulleys.
| 10. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Remove the 5 bolts and V-ribbed belt tensioner.
| 11. REMOVE OIL FILTER ELEMENT |
![]() |
Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
| *1 | Pipe |
| *2 | Hose |
![]() |
Remove the oil filter drain plug.
![]() |
Install the pipe to the oil filter cap.
| *1 | Cap |
| *2 | Valve |
| *3 | Pipe |
| *4 | O-Ring |
| *5 | Hose |
![]() |
Check that oil is drained from the oil filter. Then, disconnect the pipe as shown in the illustration and remove the O-ring.
![]() |
Using SST, remove the oil filter cap.
| *1 | Oil Filter Bracket Clip |
![]() |
Remove the oil filter element and O-ring from the oil filter cap.
| *1 | O-Ring |
| 12. REMOVE OIL FILTER BRACKET |
![]() |
Remove the 2 nuts, bolt, oil filter bracket and gasket.
| 13. REMOVE CRANKSHAFT PULLEY |
![]() |
Using SST, hold the crankshaft pulley and loosen the pulley bolt. Continue to loosen the bolt until only 2 or 3 threads are screwed into the crankshaft.
![]() |
Using the pulley set bolt and SST, remove the crankshaft pulley and pulley bolt.
| 14. REMOVE NO. 1 OIL PIPE |
![]() |
Remove the 2 oil pipe unions, oil control valve filter LH, 3 gaskets and No. 1 oil pipe.
| 15. REMOVE NO. 2 OIL PIPE |
![]() |
Remove the 2 oil pipe unions, oil control valve filter RH, 3 gaskets and No. 2 oil pipe.
| 16. DISCONNECT FUEL PIPE SUB-ASSEMBLY |
Remove the 2 bolts and disconnect the fuel pipe.
| 17. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH |
![]() |
Remove the 12 bolts, seal washer, cylinder head cover and gasket.
![]() |
Remove the 3 gaskets.
| 18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Remove the 12 bolts, seal washer, cylinder head cover and gasket.
![]() |
Remove the 3 gaskets.
| 19. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 10 bolts and 2 nuts.
![]() |
Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.
| *1 | Oil Pan Seal Cutter |
| 20. REMOVE OIL STRAINER SUB-ASSEMBLY |
![]() |
Remove the 2 nuts, oil strainer and gasket.
| 21. REMOVE OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 17 bolts and 2 nuts.
![]() |
Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.
| *A | LH Side |
| *B | RH Side |
| *a | Pry |
![]() |
Remove the 3 O-rings from the timing chain cover.
| 22. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY |
![]() |
Remove the 26 bolts and the 2 nuts.
![]() |
Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.
![]() |
Remove the oil pump gasket from the cylinder block.
| 23. REMOVE FRONT CRANKSHAFT OIL SEAL |
Using a screwdriver and wooden block, pry out the oil seal.