Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1610/13    Front Airbag Sensor RH Malfunction

DTC    B1615/14    Front Airbag Sensor LH Malfunction

for Preparation Click here


DESCRIPTION

The front airbag sensor LH and RH consists of the diagnostic circuit and the frontal deceleration sensor, etc.
If the center airbag sensor receives signals from the frontal deceleration sensor, it determines whether the SRS should be activated.
DTC B1610/13 or B1615/14 is recorded when a malfunction is detected in the front airbag sensor LH and RH circuit.

DTC Code
Detection Condition
Trouble Area
B1610/13
When one of the following conditions is met:
  1. Front airbag sensor RH malfunction
  2. Center airbag sensor malfunction
  1. Front airbag sensor RH
  2. Center airbag sensor assembly
B1615/14
When one of the following conditions is met:
  1. Front airbag sensor LH malfunction
  2. Center airbag sensor malfunction
  1. Front airbag sensor LH
  2. Center airbag sensor assembly

WIRING DIAGRAM


C158882E01


C158882E02


INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

1.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1615 is output
    A
    DTC B1610 and B1615 are not output
    B
    DTC B1610 and B1615 are output
    C
    DTC B1610 is output
    D



A
Go to step 7

B
USE SIMULATION METHOD TO CHECK (Click here)

C
Go to step 13
D


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the front airbag sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and front airbag sensor RH.

  1. Check that the connectors (on the center airbag sensor side and front airbag sensor RH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


4.CHECK FRONT AIRBAG SENSOR RH CIRCUIT

C158832E01

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A1-1 (-SR) - Body ground
    Ignition switch ON
    Below 1 V
    A1-2 (+SR) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A1-1 (-SR) - A1-2 (+SR)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A1-1 (-SR) - A1-2 (+SR)
    Always
    1 MΩ or higher
    A1-1 (-SR) - Body ground
    A1-2 (+SR) - Body ground



NG
Go to step 6
OK


5.CHECK FRONT AIRBAG SENSOR RH
C172066E01
  1. Connect the connectors to the center airbag sensor.

  1. Interchange the front airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1610 is output
    A
    DTC B1615 is output
    B
    DTC B1610 and B1615 are not output
    C

    HINT:
    Codes other than DTC B1610 and B1615 may be output at this time, but they are not related to this check.



A
Go to step 12

B
REPLACE FRONT AIRBAG SENSOR RH (Click here)
C

USE SIMULATION METHOD TO CHECK (Click here)  

6.CHECK INSTRUMENT PANEL WIRE

C158872E01

  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    AJ1-1 (-SR) - Body ground
    Ignition switch ON
    Below 1 V
    AJ1-2 (+SR) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminal 27 (-SR) and 29 (+SR) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified Condition
    AJ1-1 (-SR) - AJ1-2 (+SR)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    AJ1-1 (-SR) - AJ1-2 (+SR)
    Always
    1 MΩ or higher
    AJ1-1 (-SR) - Body ground
    AJ1-2 (+SR) - Body ground



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE 

7.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the front airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


8.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and front airbag sensor LH.

  1. Check that the connectors (on the center airbag sensor side and front airbag sensor LH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


9.CHECK FRONT AIRBAG SENSOR LH CIRCUIT

C158833E01

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A2-1 (-SL) - Body ground
    Ignition switch ON
    Below 1 V
    A2-2 (+SL) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A2-1 (-SL) - A2-2 (+SL)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A2-1 (-SL) - A2-2 (+SL)
    Always
    1 MΩ or higher
    A2-1 (-SL) - Body ground
    A2-2 (+SL) - Body ground



NG
Go to step 11
OK


10.CHECK FRONT AIRBAG SENSOR LH


    C172066E03
  1. Connect the connectors to the center airbag sensor.

  1. Interchange the front airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1610 is output
    A
    DTC B1615 is output
    B
    DTC B1610 and B1615 are not output
    C

    HINT:
    Codes other than DTC B1610 and B1615 may be output at this time, but they are not related to this check.



A
REPLACE FRONT AIRBAG SENSOR LH (Click here)

B
Go to step 12
C

USE SIMULATION METHOD TO CHECK (Click here)  

11.CHECK INSTRUMENT PANEL WIRE

C158883E01

  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    AJ8-1 (-SL) - Body ground
    Ignition switch ON
    Below 1 V
    AJ8-2 (+SL) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminal 30 (+SL) and 28 (-SL) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified Condition
    AJ8-1 (-SL) - AJ8-2 (+SL)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    AJ8-1 (-SL) - AJ8-2 (+SL)
    Always
    1 MΩ or higher
    AJ8-1 (-SL) - Body ground
    AJ8-2 (+SL) - Body ground



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE 

12.REPLACE CENTER AIRBAG SENSOR


    C167366E01
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the center airbag sensor.

    1. for Column Shift Type (Click here).

    2. for Floor Shift Type (Click here).

      HINT:
      Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1610 and B1615 are not output.

    HINT:
    Codes other than B1610 may be output at this time, but they are not related to this check.



NG
REPLACE FRONT AIRBAG SENSOR RH AND LH (Click here)
OK

END 

13.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the front airbag sensor RH and LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


14.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and front airbag sensor RH and LH.

  1. Check that the connectors (on the center airbag sensor side and front airbag sensor RH and LH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


15.CHECK FRONT AIRBAG SENSOR RH CIRCUIT

C158832E01

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A1-1 (-SR) - Body ground
    Ignition switch ON
    Below 1 V
    A1-2 (+SR) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A1-1 (-SR) - A1-2 (+SR)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A1-1 (-SR) - A1-2 (+SR)
    Always
    1 MΩ or higher
    A1-1 (-SR) - Body ground
    A1-2 (+SR) - Body ground



NG
Go to step 18
OK


16.CHECK FRONT AIRBAG SENSOR LH CIRCUIT

C158833E01

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A2-1 (-SL) - Body ground
    Ignition switch ON
    Below 1 V
    A2-2 (+SL) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A2-1 (-SL) - A2-2 (+SL)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A2-1 (-SL) - A2-2 (+SL)
    Always
    1 MΩ or higher
    A2-1 (-SL) - Body ground
    A2-2 (+SL) - Body ground



NG
Go to step 19
OK


17.REPLACE FRONT AIRBAG SENSOR RH AND LH


    C167366E01
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the front airbag sensor RH and LH (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1610 and B1615 are not output.

    HINT:
    Codes other than B1610 and B1615 may be output at this time, but they are not related to this check.

    Result 
    Result
    Proceed to
    NG (for Floor Shift Type)
    A
    NG (for Column Shift Type)
    B
    OK
    C



A
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
C

END 

18.CHECK INSTRUMENT PANEL WIRE

C158872E01

  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    AJ1-1 (-SR) - Body ground
    Ignition switch ON
    Below 1 V
    AJ1-2 (+SR) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminal 27 (-SR) and 29 (+SR) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified Condition
    AJ1-1 (-SR) - AJ1-2 (+SR)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    AJ1-1 (-SR) - AJ1-2 (+SR)
    Always
    1 MΩ or higher
    AJ1-1 (-SR) - Body ground
    AJ1-2 (+SR) - Body ground



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE 

19.CHECK INSTRUMENT PANEL WIRE

C158883E01

  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    AJ8-1 (-SL) - Body ground
    Ignition switch ON
    Below 1 V
    AJ8-2 (+SL) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminal 30 (+SL) and 28 (-SL) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified Condition
    AJ8-1 (-SL) - AJ8-2 (+SL)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    AJ8-1 (-SL) - AJ8-2 (+SL)
    Always
    1 MΩ or higher
    AJ8-1 (-SL) - Body ground
    AJ8-2 (+SL) - Body ground



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE