WINDOW DEFOGGER SYSTEM > Rear Window Defogger System does not Operate |

| 1.PERFORM ACTIVE TEST USING TECHSTREAM (DEFOGGER RELAY) |
Select the Active Test, using the Techstream to generate a control command, and then check that the rear window defogger operates (Click here).
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Defogger Relay (Rear) | Defogger relay | ON or OFF | - |
|
| ||||
| OK | |
| 2.CHECK AIR CONDITIONING CONTROL ASSEMBLY |
Temporarily replace the air conditioning control assembly with a new or normally functioning one (Click here).
Check that the malfunction disappears.
|
| ||||
| OK | ||
| ||
| 3.INSPECT FUSE (DEFOG, ECU-IG No.1) |
Remove the DEFOG H-fuse from the engine room relay block, junction block.
Remove the ECU-IG No.1 fuse from the driver side junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| DEFOG H-fuse | Always | Below 1 Ω |
| ECU-IG No.1 fuse | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.INSPECT DEFOGGER RELAY (DEFOG) |
![]() |
Remove the defogger relay (DEFOG) from the engine room relay block, junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 4 | When battery voltage is not applied between terminals 1 and 2 | Below 1 Ω |
| 3 - 5 | 10 kΩ or higher | |
| 3 - 4 | When battery voltage is applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (DEFOGGER RELAY - BATTERY AND AIR CONDITIONING AMPLIFIER) |
![]() |
Remove the defogger relay (DEFOG) from the engine room relay block, junction block.
Disconnect the J19 air conditioning amplifier connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Defogger relay (DEFOG) terminal 2 - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch OFF | Below 1 V | |
| Defogger relay (DEFOG) terminal 5 - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Defogger relay (DEFOG) terminal 1 - J19-38 (RDEF) | Always | Below 1 Ω |
| Defogger relay (DEFOG) terminal 1 or J19-38 (RDEF) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (DEFOGGER WIRE - DEFOGGER RELAY AND BODY GROUND) |

Disconnect the P9 and P10 rear window glass (defogger wire) connectors.
Remove the defogger relay (DEFOG) from the engine room relay block, junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P9-1 (B) - Defogger relay (DEFOG) terminal 3 | Always | Below 1 Ω |
| P10-1 (E) - Body ground | Always | Below 1 Ω |
| Defogger relay (DEFOG) terminal 4 - Body ground | Always | Below 1 Ω |
| P9-1 (B) or Defogger relay (DEFOG) terminal 3 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.CHECK BACK WINDOW GLASS (DEFOGGER WIRE) |
Perform the on-vehicle inspection, check that the window defogger system operates normally (Click here).
|
| ||||
| OK | ||
| ||