Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW MASTER SWITCH

POWER WINDOW MASTER SWITCH > ON-VEHICLE INSPECTION

for Preparation Click here



1. CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/o Jam Protection Function)



B166134E12


Text in Illustration 
*A
for Regular Cab
*B
for Double Cab, for CrewMax
*1
Window Lock Switch
*2
Driver Switch
*3
Front Passenger Switch
*4
Rear LH Switch
*5
Rear RH Switch
-
-
*a
Component with harness connected
(Power Window Regulator Master Switch assembly)
*b
for Driver Side
*c
Front Passenger Side
*d
for Rear LH Side
*e
for Rear RH Side
-
-
  1. for Regular Cab:

    1. Remove the power window regulator master switch assembly (Click here).

    2. Reconnect the switch connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for Driver Switch: 
      Tester Connection
      Switch Condition
      Specified Condition
      N2-10 (U) - N2-7 (E)
      Ignition switch ON, driver side door power window regulator switch OFF → UP
      Below 1 V → 11 to 14 V
      N2-12 (D) - N2-7 (E)
      Ignition switch ON, driver side door power window regulator switch OFF → DOWN
      N2-12 (D) - N2-7 (E)
      Ignition switch ON, driver side door glass fully closed → power window AUTO DOWN operation → driver side door glass fully open
      Below 1 V → 11 to 14 V → Below 1 V
      for Front Passenger Switch: 
      Tester Connection
      Switch Condition
      Specified Condition
      N2-16 (U) - N2-7 (E)
      Ignition switch ON, front passenger side door power window regulator switch OFF → UP
      Below 1 V → 11 to 14 V
      N2-18 (D) - N2-7 (E)
      Ignition switch ON, front passenger side door power window regulator switch OFF → DOWN

  1. for Double Cab:

    1. Remove the power window regulator master switch assembly (Click here).

    2. Reconnect the switch connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for Driver Switch: 
      Tester Connection
      Switch Condition
      Specified Condition
      N2-3 (U) - N2-1 (E)
      Ignition switch ON, driver side door power window regulator switch OFF → UP
      Below 1 V → 11 to 14 V
      N2-4 (D) - N2-1 (E)
      Ignition switch ON, driver side door power window regulator switch OFF → DOWN
      N2-4 (D) - N2-1 (E)
      Ignition switch ON, driver side door glass fully closed → power window AUTO DOWN operation → driver side door glass fully open
      Below 1 V → 11 to 14 V → Below 1 V
      for Front Passenger Switch: 
      Tester Connection
      Switch Condition
      Specified Condition
      N2-16 (U) - N2-1 (E)
      Ignition switch ON, front passenger side door power window regulator switch OFF → UP
      Below 1 V → 11 to 14 V
      N2-15 (D) - N2-1 (E)
      Ignition switch ON, front passenger side door power window regulator switch OFF → DOWN
      for Rear Switch LH: 
      Tester Connection
      Switch Condition
      Specified Condition
      N2-12 (U) - N2-1 (E)
      Ignition switch ON, rear LH side door power window regulator switch OFF → UP
      Below 1 V → 11 to 14 V
      N2-13 (D) - N2-1 (E)
      Ignition switch ON, rear LH side door power window regulator switch OFF → DOWN
      for Rear Switch RH: 
      Tester Connection
      Switch Condition
      Specified Condition
      N2-10 (U) - N2-1 (E)
      Ignition switch ON, rear RH side door power window regulator switch OFF → UP
      Below 1 V → 11 to 14 V
      N2-18 (D) - N2-1 (E)
      Ignition switch ON, rear RH side door power window regulator switch OFF → DOWN

  1. for CrewMax:

    1. Remove the power window regulator master switch assembly (Click here).

    2. Reconnect the switch connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for Driver Switch: 
      Tester Connection
      Switch Condition
      Specified Condition
      N2-3 (U) - N2-1 (E)
      Ignition switch ON, driver side door power window regulator switch OFF → UP
      Below 1 V → 11 to 14 V
      N2-4 (D) - N2-1 (E)
      Ignition switch ON, driver side door power window regulator switch OFF → DOWN
      N2-4 (D) - N2-1 (E)
      Ignition switch ON, driver side door glass fully closed → power window AUTO DOWN operation → driver side door glass fully open
      Below 1 V → 11 to 14 V → Below 1 V
      for Front Passenger Switch: 
      Tester Connection
      Switch Condition
      Specified Condition
      N2-16 (U) - N2-1 (E)
      Ignition switch ON, front passenger side door power window regulator switch OFF → UP
      Below 1 V → 11 to 14 V
      N2-15 (D) - N2-1 (E)
      Ignition switch ON, front passenger side door power window regulator switch OFF → DOWN
      for Rear LH Switch: 
      Tester Connection
      Switch Condition
      Specified Condition
      N2-12 (U) - N2-1 (E)
      Ignition switch ON, rear LH side door power window regulator switch OFF → UP
      Below 1 V → 11 to 14 V
      N2-13 (D) - N2-1 (E)
      Ignition switch ON, rear LH side door power window regulator switch OFF → DOWN
      for Rear RH Switch: 
      Tester Connection
      Switch Condition
      Specified Condition
      N2-10 (U) - N2-1 (E)
      Ignition switch ON, rear RH side door power window regulator switch OFF → UP
      Below 1 V → 11 to 14 V
      N2-18 (D) - N2-1 (E)
      Ignition switch ON, rear RH side door power window regulator switch OFF → DOWN



2. CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/ Jam Protection Function)



B231346E03


Text in Illustration 
*1
Window Lock Switch
*2
Driver Switch
*3
Rear RH Switch
*4
Rear LH Switch
*a
Component with harness connected
(Master Switch Assembly)
*b
for Driver Side
*c
for Rear LH Side
*d
for Rear RH Side
  1. Remove the power window regulator master switch assembly (Click here).

  1. Reconnect the switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for Driver Switch: 
    Tester Connection
    Switch Condition
    Specified Condition
    N2-4 (UP) - N2-1 (E)
    Ignition switch ON, driver side door power window regulator switch OFF → UP
    Below 1 V → 11 to 14 V
    N2-4 (UP) - N2-1 (E)
    Ignition switch ON, driver side door glass fully closed → power window AUTO UP operation → driver side door glass fully open
    N2-5 (DOWN) - N2-1 (E)
    Ignition switch ON, driver side door power window regulator switch OFF → DOWN
    N2-5 (DOWN) - N2-1 (E)
    Ignition switch ON, driver side door glass fully closed → power window AUTO DOWN operation → driver side door glass fully open
    Below 1 V → 11 to 14 V → Below 1 V
    for Rear LH Switch: 
    Tester Connection
    Switch Condition
    Specified Condition
    N2-12 (U) - N2-1 (E)
    Ignition switch ON, rear LH side door power window regulator switch OFF → UP
    Below 1 V → 11 to 14 V
    N2-15 (D) - N2-1 (E)
    Ignition switch ON, rear LH side door power window regulator switch OFF → DOWN
    for Rear RH Switch: 
    Tester Connection
    Switch Condition
    Specified Condition
    N2-10 (U) - N2-1 (E)
    Ignition switch ON, rear RH side door power window regulator switch OFF → UP
    Below 1 V → 11 to 14 V
    N2-16 (D) - N2-1 (E)
    Ignition switch ON, rear RH side door power window regulator switch OFF → DOWN