Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here


HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

    NOTICE:
    1. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
    2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


JUNCTION CONNECTOR


  1. No. 1 Junction Connector


    C227477E10


    Text in Illustration 
    *a
    for No. 2 Junction Connector
    *b
    for DLC3
    *c
    for Center Airbag Sensor Assembly
    *d
    for Combination Meter Assembly
    *e
    for Main Body ECU (Driver Side Junction Block Assembly)
    *f
    for Steering Angle Sensor
    *g
    for Brake Actuator Assembly (Skid Control ECU)
    -
    -

    No. 1 Junction Connector
    Wiring Color
    Connected for
    J75-1 (CANH)
    R
    No. 2 junction connector
    J75-12 (CANL)
    W
    J75-2 (CANH)
    V
    DLC3
    J75-13 (CANL)
    W
    J75-3 (CANH)
    BR
    Center airbag sensor assembly
    J75-14 (CANL)
    W
    J75-4 (CANH)
    SB
    Combination meter assembly
    J75-15 (CANL)
    W
    J75-5 (CANH)
    L
    Main body ECU (driver side junction block assembly)
    J75-16 (CANL)
    W
    J75-6 (CANH)
    G
    Steering angle sensor
    J75-17 (CANL)
    W
    J75-8 (CANH)
    B
    Brake actuator assembly (skid control ECU)
    J75-19 (CANL)
    W



  2. No. 2 Junction Connector


    C227477E11


    Text in Illustration 
    *a
    for Air Conditioning Amplifier Assembly
    *b
    for 4WD Control ECU (for 4WD)
    *c
    for ECM
    *d
    for No. 1 Junction Connector
    *e
    for Bus Buffer ECU (w/ Bus Buffer ECU)
    *f
    for Network Gateway ECU (w/ Blind Spot Monitor System)
    *g
    1. for Radio and Display Receiver Assembly (w/ Audio and Visual System)
    2. for Navigation Receiver Assembly (w/ Navigation System)
    -
    -

    No. 2 Junction Connector
    Wiring Color
    Connected for
    J74-1 (CANH)
    B
    Air conditioning amplifier assembly
    J74-12 (CANL)
    W
    J74-2 (CANH)
    BE
    4WD control ECU*1
    J74-13 (CANL)
    W
    J74-3 (CANH)
    GR
    ECM
    J74-14 (CANL)
    W
    J74-4 (CANH)
    R
    No. 1 junction connector
    J74-15 (CANL)
    W
    J74-5 (CANH)
    P
    Bus buffer ECU*2
    J74-16 (CANL)
    W
    J74-6 (CANH)
    SB
    Network gateway ECU*3
    J74-17 (CANL)
    W
    J74-7 (CANH)
    LG
    1. Radio and display receiver assembly*4
    2. Navigation receiver assembly*5
    J74-18 (CANL)
    W
    1. *1: for 4WD
    2. *2: w/ Bus Buffer ECU
    3. *3: w/ Blind Spot Monitor System
    4. *4: w/ Audio and Visual System
    5. *5: w/ Navigation System



  3. No. 3 Junction Connector (w/ Seat Memory)


    C227477E12


    Text in Illustration 
    *a
    for Combination Meter Assembly
    *b
    for Multiplex Tilt and Telescopic ECU
    *c
    for Front Power Seat Control ECU and Switch LH
    *d
    for Main Body ECU (Driver Side Junction Block Assembly)
    *e
    for Outer Mirror Control ECU Assembly
    -
    -

    No. 3 Junction Connector
    Wiring Color
    Connected for
    J76-1 (CANH)
    Y
    Combination meter assembly
    J76-12 (CANL)
    W
    J76-2 (CANH)
    BE
    Multiplex tilt and telescopic ECU
    J76-13 (CANL)
    W
    J76-3 (CANH)
    GR
    Front power seat control ECU and switch LH
    J76-14 (CANL)
    W
    J76-4 (CANH)
    B
    Main body ECU (driver side junction block assembly)
    J76-15 (CANL)
    W
    J76-5 (CANH)
    LG
    Outer mirror control ECU assembly
    J76-16 (CANL)
    W



  4. No. 4 Junction Connector (w/ Blind Spot Monitor System)


    C239215E07


    Text in Illustration 
    *a
    for Network Gateway ECU
    *b
    for No. 5 Junction Connector
    *c
    for Blind Spot Monitor Sensor RH
    -
    -

    No. 4 Junction Connector
    Wiring Color
    Connected for
    R17-1 (CANH)
    G
    Network gateway ECU
    R17-4 (CANL)
    W
    R17-2 (CANH)
    L
    No. 5 junction connector
    R17-3 (CANL)
    W
    R17-5 (CANH)
    R
    Blind spot monitor sensor RH
    R17-8 (CANL)
    W



  5. C210060E62
  6. No. 5 Junction Connector (w/ Blind Spot Monitor System)
    Text in Illustration 
    *a
    for No. 4 Junction Connector

    No. 5 Junction Connector
    Wiring Color
    Connected for
    J77-3 (CANH)
    B
    No. 4 junction connector
    J77-2 (CANL)
    W


CHECK DLC3
C253362E28
  1. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    J17-6 (CANH) - J17-14 (CANL)
    V - W
    Ignition switch off
    54 to 69 Ω
    J17-6 (CANH) - J17-4 (CG)
    V - W-B
    Ignition switch off
    200 Ω or higher
    J17-14 (CANL) - J17-4 (CG)
    W - W-B
    Ignition switch off
    200 Ω or higher
    J17-6 (CANH) - J17-16 (BAT)
    V - P
    Ignition switch off
    6 kΩ or higher
    J17-14 (CANL) - J17-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher


CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

C240485E04

  1. Disconnect the A17 brake actuator assembly (skid control ECU) connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A17-12 (CANH) - A17-13 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    A17-12 (CANH) - A17-16 (GND1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    A17-13 (CANL) - A17-16 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A17-12 (CANH) - A17-1 (+BM)
    B - L
    Ignition switch off
    6 kΩ or higher
    A17-13 (CANL) - A17-1 (+BM)
    W - L
    Ignition switch off
    6 kΩ or higher


CHECK MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

E146976E06


Text in Illustration 
*A
for V Bus
*b
for MS Bus
  1. Disconnect the J2 and DB main body ECU (driver side junction block assembly) connectors.

  2. Measure the resistance according to the value(s) in the table below.

    for V Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    J2-5 (CANH) - J2-6 (CANL)
    L - W
    Ignition switch off
    54 to 69 Ω
    J2-5 (CANH) - DB-21 (GND1)
    L - B
    Ignition switch off
    200 Ω or higher
    J2-6 (CANL) - DB-21 (GND1)
    W - B
    Ignition switch off
    200 Ω or higher
    J2-5 (CANH) - DB-13 (BECU)
    L - GR
    Ignition switch off
    6 kΩ or higher
    J2-6 (CANL) - DB-13 (BECU)
    W - GR
    Ignition switch off
    6 kΩ or higher

    for MS Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    J2-16 (CANP) - J2-15 (CANN)
    B - W
    Ignition switch off
    108 to 132 Ω
    J2-16 (CANP) - DB-21 (GND1)
    B - B
    Ignition switch off
    200 Ω or higher
    J2-15 (CANN) - DB-21 (GND1)
    W - B
    Ignition switch off
    200 Ω or higher
    J2-16 (CANP) - DB-13 (BECU)
    B - GR
    Ignition switch off
    6 kΩ or higher
    J2-15 (CANN) - DB-13 (BECU)
    W - GR
    Ignition switch off
    6 kΩ or higher


CHECK ECM

C159489E34

  1. Disconnect the A24 and D74 ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A24-10 (CANH) - A24-11 (CANL)
    GR - W
    Ignition switch off
    108 to 132 Ω
    A24-10 (CANH) - D74-81 (E1)
    GR - BR
    Ignition switch off
    200 Ω or higher
    A24-11 (CANL) - D74-81 (E1)
    W - BR
    Ignition switch off
    200 Ω or higher
    A24-10 (CANH) - A24-1 (BATT)
    GR - L
    Ignition switch off
    6 kΩ or higher
    A24-11 (CANL) - A24-1 (BATT)
    W - L
    Ignition switch off
    6 kΩ or higher


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

C159478E08

  1. Disconnect the J19 air conditioning amplifier assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    J19-11 (CANH) - J19-12 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    J19-11 (CANH) - J19-14 (GND)
    B - W-B
    Ignition switch off
    200 Ω or higher
    J19-12 (CANL) - J19-14 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    J19-11 (CANH) - J19-21 (B)
    B - BR
    Ignition switch off
    6 kΩ or higher
    J19-12 (CANL) - J19-21 (B)
    W - BR
    Ignition switch off
    6 kΩ or higher


CHECK CENTER AIRBAG SENSOR ASSEMBLY

C162022E05

  1. Disconnect the J46 center airbag sensor assembly connector.

    1. for Column Shift Type: Click here
    2. for Floor Shift Type: Click here

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    J46-13 (CANH) - J46-22 (CANL)
    BR - W
    Ignition switch off
    54 to 69 Ω
    J46-13 (CANH) - J46-25 (E1)
    BR - W-B
    Ignition switch off
    200 Ω or higher
    J46-22 (CANL) - J46-25 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    J46-13 (CANH) - J17-16 (BAT)
    BR - P
    Ignition switch off
    6 kΩ or higher
    J46-22 (CANL) - J17-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher


CHECK COMBINATION METER ASSEMBLY

C159488E10


Text in Illustration 
*A
for V Bus
*b
for MS Bus
  1. Disconnect the J28 combination meter assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    for V Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    J28-39 (CANH) - J28-40 (CANL)
    SB - W
    Ignition switch off
    108 to 132 Ω
    J28-39 (CANH) - J28-24 (ES)
    SB - W-B
    Ignition switch off
    200 Ω or higher
    J28-40 (CANL) - J28-24 (ES)
    W - W-B
    Ignition switch off
    200 Ω or higher
    J28-39 (CANH) - J28-1 (B)
    SB - LG
    Ignition switch off
    6 kΩ or higher
    J28-40 (CANL) - J28-1 (B)
    W - LG
    Ignition switch off
    6 kΩ or higher

    for MS Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    J28-18 (MSCH) - J28-19 (MSCL)
    Y - W
    Ignition switch off
    108 to 132 Ω
    J28-18 (MSCH) - J28-24 (ES)
    Y - W-B
    Ignition switch off
    200 Ω or higher
    J28-19 (MSCL) - J28-24 (ES)
    W - W-B
    Ignition switch off
    200 Ω or higher
    J28-18 (MSCH) - J28-1 (B)
    Y - LG
    Ignition switch off
    6 kΩ or higher
    J28-19 (MSCL) - J28-1 (B)
    W - LG
    Ignition switch off
    6 kΩ or higher


CHECK NETWORK GATEWAY ECU (w/ Blind Spot Monitor System)

C242684E07


Text in Illustration 
*A
for V Bus
*B
for V2 Bus
  1. Disconnect the J123 network gateway ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    for V Bus  
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    J123-16 (CA1H) - J123-15 (CA1L)
    SB - W
    Ignition switch off
    54 to 69 Ω
    J123-16 (CA1H) - J123-4 (GND)
    SB - W-B
    Ignition switch off
    200 Ω or higher
    J123-15 (CA1L) - J123-4 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    J123-16 (CA1H) - J123-2 (BATT)
    SB - Y
    Ignition switch off
    6 kΩ or higher
    J123-15 (CA1L) - J123-2 (BATT)
    W - Y
    Ignition switch off
    6 kΩ or higher

    for V2 Bus  
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    J123-13 (CA2H) - J123-12 (CA2L)
    G - W
    Ignition switch off
    108 to 132 Ω
    J123-13 (CA2H) - J123-4 (GND)
    G - W-B
    Ignition switch off
    200 Ω or higher
    J123-12 (CA2L) - J123-4 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    J123-13 (CA2H) - J123-2 (BATT)
    G - Y
    Ignition switch off
    6 kΩ or higher
    J123-12 (CA2L) - J123-2 (BATT)
    W - Y
    Ignition switch off
    6 kΩ or higher


CHECK BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor System)

C270134E13


Text in Illustration 
*A
for V2 Bus
*B
for Sensor Bus
  1. Disconnect the S6 blind spot monitor sensor RH connector.

  2. Measure the resistance according to the value(s) in the table below.

    for V2 Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    S6-2 (CA1P) - S6-7 (CA1N)
    R - W
    Ignition switch off
    54 to 69 Ω
    S6-2 (CA1P) - S6-10 (BRGD)
    R - W-B
    Ignition switch off
    200 Ω or higher
    S6-7 (CA1N) - S6-10 (BRGD)
    W - W-B
    Ignition switch off
    200 Ω or higher
    S6-2 (CA1P) - J17-16 (BAT)
    R - P
    Ignition switch off
    6 kΩ or higher
    S6-7 (CA1N) - J17-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher

    for Sensor Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    S6-1 (CA2P) - S6-6 (CA2N)
    LG - W
    Ignition switch off
    108 to 132 Ω
    S6-1 (CA2P) - S6-10 (BRGD)
    LG - W-B
    Ignition switch off
    200 Ω or higher
    S6-6 (CA2N) - S6-10 (BRGD)
    W - W-B
    Ignition switch off
    200 Ω or higher
    S6-1 (CA2P) - J17-16 (BAT)
    LG - P
    Ignition switch off
    6 kΩ or higher
    S6-6 (CA2N) - J17-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher


CHECK BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)

C270134E14

  1. Disconnect the S5 blind spot monitor sensor LH connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    S5-1 (CA2P) - S5-6 (CA2N)
    LG - W
    Ignition switch off
    108 to 132 Ω
    S5-1 (CA2P) - S5-10 (BLGD)
    LG - W-B
    Ignition switch off
    200 Ω or higher
    S5-6 (CA2N) - S5-10 (BLGD)
    W - W-B
    Ignition switch off
    200 Ω or higher
    S5-1 (CA2P) - J17-16 (BAT)
    LG - P
    Ignition switch off
    6 kΩ or higher
    S5-6 (CA2N) - J17-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher


CHECK STEERING ANGLE SENSOR

C159491E05

  1. Disconnect the J6 steering angle sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    J6-10 (CANH) - J6-9 (CANL)
    G - W
    Ignition switch off
    54 to 69 Ω
    J6-10 (CANH) - J6-2 (ESS)
    G - W-B
    Ignition switch off
    200 Ω or higher
    J6-9 (CANL) - J6-2 (ESS)
    W - W-B
    Ignition switch off
    200 Ω or higher
    J6-10 (CANH) - J6-3 (BAT)
    G - R
    Ignition switch off
    6 kΩ or higher
    J6-9 (CANL) - J6-3 (BAT)
    W - R
    Ignition switch off
    6 kΩ or higher


CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio and Visual System)

C290645E01

  1. Disconnect the J137 and J139 radio and display receiver assembly connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    J139-9 (CANH) - J139-10 (CANL)
    LG - W
    Ignition switch off
    54 to 69 Ω
    J139-9 (CANH) - J137-7 (GND1)
    LG - W-B
    Ignition switch off
    200 Ω or higher
    J139-10 (CANL) - J137-7 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    J139-9 (CANH) - J137-4 (+B1)
    LG - V
    Ignition switch off
    6 kΩ or higher
    J139-10 (CANL) - J137-4 (+B1)
    W - V
    Ignition switch off
    6 kΩ or higher


CHECK NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)

C290645E02

  1. Disconnect the J133 and J135 navigation receiver assembly connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    J135-9 (CANH) - J135-10 (CANL)
    LG - W
    Ignition switch off
    54 to 69 Ω
    J135-9 (CANH) - J133-7 (GND1)
    LG - W-B
    Ignition switch off
    200 Ω or higher
    J135-10 (CANL) - J133-7 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    J135-9 (CANH) - J133-4 (+B1)
    LG - V
    Ignition switch off
    6 kΩ or higher
    J135-10 (CANL) - J133-4 (+B1)
    W - V
    Ignition switch off
    6 kΩ or higher


CHECK 4WD CONTROL ECU (for 4WD)

C289499E02

  1. Disconnect the A25 4WD control ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A25-23 (CANH) - A25-22 (CANL)
    BE - W
    Ignition switch off
    54 to 69 Ω
    A25-23 (CANH) - A26-5 (GND)
    BE - W-B
    Ignition switch off
    200 Ω or higher
    A25-22 (CANL) - A26-5 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A25-23 (CANH) - A25-6 (B)
    BE - G
    Ignition switch off
    6 kΩ or higher
    A25-22 (CANL) - A25-6 (B)
    W - G
    Ignition switch off
    6 kΩ or higher


CHECK BUS BUFFER ECU (w/ Bus Buffer ECU)
C288321E02
  1. Disconnect the J59 bus buffer ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    J59-3 (CAN+) - J59-2 (CAN-)
    P - W
    Ignition switch off
    54 to 69 Ω


CHECK FRONT POWER SEAT CONTROL ECU AND SWITCH LH (w/ Seat Memory)

B219506E48

  1. Disconnect the Z9 and Z10 front power seat control ECU and switch LH connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    Z10-8 (CANP) - Z10-7 (CANN)
    L - W
    Ignition switch off
    54 to 69 Ω
    Z10-8 (CANP) - Z9-2 (GND1)
    L - W-B
    Ignition switch off
    200 Ω or higher
    Z10-7 (CANN) - Z9-2 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    Z10-8 (CANP) - Z9-7 (+B1)
    L - W
    Ignition switch off
    6 kΩ or higher
    Z10-7 (CANN) - Z9-7 (+B1)
    W - W
    Ignition switch off
    6 kΩ or higher


CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Seat Memory)

C159485E05

  1. Disconnect the N7 and N8 outer mirror control ECU assembly connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    N8-1 (CAN) - N8-21 (CGND)
    LG - W
    Ignition switch off
    54 to 69 Ω
    N8-1 (CAN) - N7-9 (GND)
    LG - W-B
    Ignition switch off
    200 Ω or higher
    N8-21 (CGND) - N7-9 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    N8-1 (CAN) - N7-3 (B)
    LG - R
    Ignition switch off
    6 kΩ or higher
    N8-21 (CGND) - N7-3 (B)
    W - R
    Ignition switch off
    6 kΩ or higher


CHECK MULTIPLEX TILT AND TELESCOPIC ECU (w/ Seat Memory)

C159486E05

  1. Disconnect the J47 multiplex tilt and telescopic ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    J47-5 (CANH) - J47-14 (CANL)
    BE - W
    Ignition switch off
    54 to 69 Ω
    J47-5 (CANH) - J47-11 (GND)
    BE - W-B
    Ignition switch off
    200 Ω or higher
    J47-14 (CANL) - J47-11 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    J47-5 (CANH) - J47-2 (+B)
    BE - P
    Ignition switch off
    6 kΩ or higher
    J47-14 (CANL) - J47-2 (+B)
    W - P
    Ignition switch off
    6 kΩ or higher